How to Design A Power Factor Correction (PFC) 400 V Rectifier Using 200 V eGaN® FETs
Acknowledgement - This application note and associated hardware was developed in collaboration with Semiconductor Power Electronics Center (SPEC) at University of Texas at Austin.
Motivation
The expansion of applications such as cloud computing, wearables, machine learning, autonomous driving, and IoT drive us towards an even more data-intensive world, increasing demands on data centers and power consumption [1, 2]. The importance of efficiency, power density, and cost of the AC to DC switching power supply is driving innovative solutions that eGaN FETs can solve to yield ultra-high efficiency power factor correction (PFC) front-end rectifier solutions that are the focus of this how-to-application note.
The 4-level Flying Capacitor Multi-Level (FCML) totem-pole bridgeless PFC converter
The conventional 2-level totem-pole bridgeless PFC topology has been a popular choice to achieve high efficiency using 650 V rated GaN FETs but does not address the power density and loss limitations of the main inductor [3]-[5]. The 4-level flying capacitor multi-level (FCML) totem-pole bridgeless PFC topology is an alternative that can utilize 200 V eGaN FETs, that can operate to the maximum grid line voltage of 274 VACRMS, and make use of the volt-seconds reduction and frequency multiplication for the inductor to significantly increase the power density and yield a high efficiency solution. The power schematic of the FCML-totem-pole bridgeless PFC rectifier is shown in figure 1. An added benefit of the 4-level FCML -totem-pole bridgeless PFC rectifier topology is that due to the low inductance required it minimizes the input current harmonic distortion and can maintain switching even with the highest peak line voltage.
Figure 1. 4-Level flying capacitor multi-level eGaN FET totem-pole PFC rectifier schematic
The 200 V rated EPC2215 for the 4-level FCML totem-pole PFC converter
One of the many benefits of using a multi-level topology is that lower voltage devices can be used. In this 4-level topology, six, cascade connected, high frequency devices (Q1 through Q6) are used in the high frequency leg shown in figure 1. The output DC voltage is set to 400 V so the voltage stress for each of the high frequency devices is only 133 V, plus margin, ensuring that 200 V devices are well suited for this topology. The 200 V rated EPC2215 eGaN FET, with RDS(on) of 8 mΩ shown in figure 2, offers low switching loss, low driving power consumption, and zero reverse recovery compared to traditional silicon devices, enabling a high efficiency solution.
Figure 2. Photo of the bump side of 200 V rated, 8 mΩ, EPC2215
Figure 3 shows a size comparison between the EPC2215 and close match MOSFET equivalent that is 15 times larger and will consume 6.5 times more gate power. In addition, the higher output capacitance will also increase the switching losses for the MOSFET compared to the GaN FET.
Figure 3. Device size comparison between the EPC2215 and closest match MOSFET counterpart, both are rated at 200 V
Experimental validation
A 2.5 kW, 4-level flying capacitor multilevel (FCML) GaN FET totem-pole PFC converter was built and is shown in figure 4 [7]. The experimental unit comprises multiple cards; 1) a mother board with EMI filter, housekeeping power supply and bulk output capacitance, 2) a controller card and, 3) the GaN FET flying capacitor multi-level converter card.
Figure 4. Photo of the (a) complete PFC rectifier and (b) the FCML bridgeless totem pole converter card
Figure 5 shows the measured input AC voltage, the well-controlled inductor current and the multi-level switch-node waveforms when the converter is operating with 240 VACRMS input voltage and delivering 2.5 kW into a 400 VDC load.
Figure 5. Measured waveforms of the inductor current (IL), AC input voltage (VAC), and switch-node voltage (VSW) when delivering 2400 W into the 400 VDC load
The overall power efficiency of the 4-level FCML totem-pole GaN FET PFC is shown in figure 6 up to 2.5 kW with a peak efficiency of 99.25% at 1.4 kW and remains above 99% from 900 W and up.
Figure 6. Power efficiency of 4-level FCML totem-pole GaN FET PFC converter
Conclusion
A high efficiency, high power density, 2.5 kW capable eGaN FET-based 4-level flying capacitor multi-level bridgeless totem-pole rectifier that is suitable for data center applications was presented. The 200 V rated, 8 mΩ, EPC2215 was used in the high frequency leg that resulted in a converter that exceeded 99% efficiency from 900 W through 2.5 kW with a peak of 99.25% at 1.4 kW. The complete converter solution has a power density of 125 W/in3 and includes the EMI filter, bulk output capacitors, controller card, and housekeeping power supply. The advantageous characteristics of eGaN FETs [6] allowed this converter to achieve high power density, ultra-high efficiency, and low harmonic distortion.
- +1 Like
- Add to Favorites
Recommend
- Sharge Selects GaN FETs EPC2218 from EPC for High-power USB PD Charger Retro 67 to Achieve the Most Efficient Power Conversion
- New Automotive Qualified GaN FETs EPC2204A and EPC2218A for Vehicle Electronics and Advanced Autonomy from EPC
- Design Higher Resolution Lidar Systems with New Automotive-Qualified GaN FET EPC2252 for Advanced Autonomy from EPC
- EPC‘s New 200 V eGaN FETs Double The Performance Edge over The Aging Silicon Power MOSFET
- Automotive AEC Q101 Qualified 65V eGaN FET EPC2219 Enables Higher Resolution for Lidar Systems
- EPC Introduces The 40 V, 1.6 Milliohm EPC2069 EGaN® FET, it Can Range From 500 W to 2 KW and Exceed 98% Efficiency
- EPC Introduces EPC9157 48V to 12V Demo Board Featuring EPC eGaN FETs and New Renesas DC-DC Controller
- EPC Announces a New 3-phase BLDC Motor Drive Inverter Using the EPC2065 EGaN® FET
This document is provided by Sekorm Platform for VIP exclusive service. The copyright is owned by Sekorm. Without authorization, any medias, websites or individual are not allowed to reprint. When authorizing the reprint, the link of www.sekorm.com must be indicated.