IMP2525 USB High-Side Power Switch
●0.14Q "ON" resistance at 3V
●MIC2525 pin compatible
■The IMP2525 high-side power switch IC is designed for self-powered and bus-powered Universal Serial Bus (USB) power supply and power management applications. The IMP2525 conforms to USB standards with a low output switch ON-resistance (RON) and minimal voltage drop across the switch. The fault current is limited to 750mA typically, and a flag output conveys fault conditions to the local USB controller. The IMP2525 provides a “Soft-Start” function that ramps up the ON-current to eliminate any excessive voltage drop on the input side that could occur due to charging a capacitive load in bus-powered applications. Self-monitoring features include thermal shutdown to prevent catastrophic switch failure from high-current loads and undervoltage lockout (UVLO) that insures that the device remains off unless there is a valid supply voltage present. The Enable input logic can be interfaced with both 3.3V and 5V logic. Both active-HIGH and active-LOW enable logic versions are available. The IMP2525 devices are available in 8-pin DIP and 8-pin SO packages.
■IMP offers a complete family of USB power management products. For dual-switch applications see the IMP2526 data sheet and for quad-switch application, see the IMP2524. The single-switch IMP2525A features a 50% lower switch resistance, 0.07Ω.
●Key Features
■Meets or exceeds USB Rev. 1.1 specification
■Low MOSFET RON (0.14Ω at 3V)
■2.7V to 5.5V input operation
■Current limiting
■Soft-start turn-on (1ms) prevents turn-on glitches
■500mA continuous load current
■MOSFET short-circuit current limit (1.25A max)
■Low supply current
◆110μA ON state current, 1μA OFF state current
■Active-LOW or Active-HIGH Enable input
■3.3V or 5V logic compatibility
■Fault Flag indicates three fault conditions:
◆Undervoltage
◆Current limit
◆Thermal shutdown
■Open-drain Fault Flag output
■2.4V Undervoltage Lockout (UVLO)
■Pin compatible with the Micrel MIC2525
IMP2525-1BM 、 IMP2525-2BM 、 IMP2525-1BN 、 IMP2525-2BN 、 IMP2525 、 IMP2525A 、 IMP2525-1 、 IMP2525-2 |
|
high-side power switch IC 、 High-Side Power Switch 、 Single switch |
|
[ USB power management ][ USB hosts ][ self-powered hubs ][ Battery-charger circuits ][ power supplies ] |
|
Datasheet |
|
|
|
Please see the document for details |
|
|
|
|
|
SO;DIP |
|
English Chinese Chinese and English Japanese |
|
08/08/05 |
|
Revision:A |
|
|
|
185 KB |
- +1 Like
- Add to Favorites
Recommend
- XBLW Xinbole Analog Chips: Signal Chain Chips (Part 3)
- More than 250 IC Manufacturers Choose Sekorm as Authorized Distributor, Building Supply Chain Security
- How To Use An EPC Development Board to Evaluate The Performance of A Given GaN FET or IC in Common Applications?
- Kinglight Driver IC Integrated LEDs for Transparent LED Display (II)
- Shindengen Launches MF2007SW High-side Nch-MOSFET Gate Driver IC with Reverse Connection and Reverse Current Protection
- Shenzhen Car Charging Chip Factory: Notes on IC Unpacking and IC Storage Methods
- Kinglight Driver IC Integrated LEDs for Transparent LED Display (I)
- MindMotion Honored with Annual Innovative IC Design Award
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.