Description of SinoGNSS K8-series GNSS Modules Common Commands
Upon receiving any GNSS modules/GPS modules for the first time, it's natural to want to verify certain essential information. To assist you with SinoGNSS K8-series GNSS modules in this process, We've compiled a list of frequently used checking commands that we'd like to share with you today.
Such as Log version/loglist/comconfig...
What do these instructions entail in terms of details? Let's delve into the specifics.
Begin by connecting our board and powering it on. Press the power button, and the software will promptly exhibit power-on information. For instance,
..............................................................................................................................................................................................................................
Loading...
CBOOT 7.3.5 BUILD (2022-Sep-29 09:48:29) // BOOT version and version development date.
SN: 01A0 09158478 2022/03/09 A11 735 // SN number and factory date
VCXO valid! Init Value:2177. // vcxo works, Init value is 2177.
Register Code is OK. // Registration code verification successful
No valid RTC time.
##DR_GNSSFreq: 0x1!
.............................................................................................................................................................................................................................
1. “LOG VERSION”
log version // Check the receiver board type, SN serial number, firmware version, FPGA version, BOOT version and other information.
.............................................................................................................................................................................................................................
<VERSION COM1 0 60.0 UNKNOWN 1930 000141.100 00000000 0000 1114
< 1
< GPSCARD "S32352K803" "0915847800000000" "CRDK-803AA-TTT-0" "610T5-22AO2-1" "7.3.5" "2022/Dec/12" "17:54:46"
.............................................................................................................................................................................................................................
✔ GPSCARD // product type
✔ "S32352K803" // Satellite Constellation Model Information(S32352); oard model(K803)
✔ "0915847800000000" // Board SN number(09057347); Reserved(00000000)
✔ "CRDK-803AA-TTT-0" // Hardware Version Information
✔ "610T5-22AO2-1" // Firmware version(610T5); FPGA Version(22AO2); Registered,if not registered, it is empty(1).
✔ “7.3.5” // BOOT version number.
.............................................................................................................................................................................................................................
Command accepted! Port: COM1. // COM1 port has received
.............................................................................................................................................................................................................................
2.“LOG LOGLIST”
log loglist // view the command information currently set by the receiver/board
.............................................................................................................................................................................................................................
#LOGLIST,COM1,0,60.0,FINESTEERING,2277,445815.800,00000000,0000,1114
.............................................................................................................................................................................................................................
3.”LOG COMCONFIG/COMCONFIGA/COMCONFIGB”
The content of ”LOG COMCONFIG/COMCONFIGA/COMCONFIGB” is the same, but they are different information formats.
➤ log comconfig // Check the serial port status and baud rate setting of the receiver/board.
The meanings of the numbers in the two columns of RxType/TxType are:
"1": Any setting of the port can input and output commands normally;
"27": Set as RTK differential port, unable to receive commands.
➤ log comconfiga // Describe the configuration of the serial port, such as baud rate, COM ID, etc.
.............................................................................................................................................................................................................................
#COMCONFIGA,COM1,0,60.0,UNKNOWN,1930,000416.550,00000000,0000,1114;COM1,115200,0,8,1,0,0,1,1,1,COM2,115200,0,8,1,0,0,1,1,1,COM3,115200,0,8,1,0,0,1,1,1,COM4,115200,0,8,1,0,0,1,1,1,COM5,115200,0,8,1,0,0,1,1,1*df1d6a86
.............................................................................................................................................................................................................................
✔ “#COMCONFIGA,COM1,0,60.0,UNKNOWN,1930,000416.550,00000000,0000,1114” // COMCONFIG Header ;
✔ “*df1d6a86” // 32-bit CRC check (only available for ASCII and binary)
➤ log comconfigb
.............................................................................................................................................................................................................................
Binary Message ID: 317 Week:2277 GPST:442741.000
.............................................................................................................................................................................................................................
There are three ways to express the data on the board: Simplified ASCII, ASCII, and Binary. All commands and messages can be expressed in any one of the three formats. In addition, ComNav boards also support RTCM2.X, RTCM3.X, RTCM, CMR, and NMEA format messages. The number of bytes of binary data is minimal.
4.“LOG SYSCONFIG”
log sysconfig // Check basic configuration, rtk configuration and work mode like PPS, Event, and SBAS.
If you want to know more details, you can check out the Blog :
Command Introduction: “log sysconfig”_ComNav Technology Ltd
(https://www.comnavtech.com/blogs_details/10.html)
5.“LOG REGLIST”
log reglist // View board function registration information
If you want to know more details, you can check out the Blog :
Explanation Of Commonly Used Registration Options_Comnav Technology Ltd
(https://www.comnavtech.com/blogs_details/6.html)
6.”UNLOGALL”
Unlogall // cancel the output of specific serial port messages. If no serial port is specified, the message output of all serial ports will be stopped.
If the serial port is specified, the message output of the specified serial port will be stopped. For example,
unlogall com1 // then the output of serial port 1 will stop.
- +1 Like
- Add to Favorites
Recommend
- The Magic Behind RTK: Delivering Unparalleled Positioning Precision
- Recommend Commands for System Integration
- How to Active the Event Option for Your GNSS Module K8 series from ComNav Technology
- ComNav‘s K8 Series GNSS Module can track the Galileo E6b signal and Has Verified the HAS Service in Most Countries
- Lighter, Thinner, Faster - ComNav Technology Introduced T20 Palm RTK
- How to Enable GNSS+INS System on ComNav K8 Series GNSS Modules
- ComNav Technology Launched GNSS High Precision Positioning Solution for Lawn Mower
- ComNav Technology‘s Z30 Portable GNSS Receiver: Precision in Your Pocket
This document is provided by Sekorm Platform for VIP exclusive service. The copyright is owned by Sekorm. Without authorization, any medias, websites or individual are not allowed to reprint. When authorizing the reprint, the link of www.sekorm.com must be indicated.