ESP32 Series Datasheet
2022-09-29
■Overview:
ESP32 is a single 2.4 GHz Wi-Fi-and-Bluetooth combo chip designed with the TSMC ultra-low-power 40 nm technology. It is designed to achieve the best power and RF performance, showing robustness, versatility and reliability in a wide variety of applications and power scenarios.
The ESP32 series of chips includes ESP32-D0WDQ6, ESP32-D0WD, ESP32-D2WD, and ESP32-S0WD. For details on part numbers and ordering information, please refer to Part Number and Ordering Information.
■Wi-Fi Key Features:
●802.11 b/g/n
●802.11 n (2.4 GHz), up to 150 Mbps
●WMM
●TX/RX A-MPDU, RX A-MSDU
●Immediate Block ACK
●Defragmentation
●Automatic Beacon monitoring (hardware TSF)
●4 × virtual Wi-Fi interfaces
●Simultaneous support for Infrastructure Station, SoftAP, and Promiscuous modes Note that when ESP32 is in Station mode, performing a scan, the SoftAP channel will be changed.
●Antenna diversity
■BT Key Features:
●Compliant with Bluetooth v4.2 BR/EDR and BLE specifications
●Class-1, class-2 and class-3 transmitter without external power amplifier
●Enhanced Power Control
●+12 dBm transmitting power
●NZIF receiver with –97 dBm BLE sensitivity
●Adaptive Frequency Hopping (AFH)
●Standard HCI based on SDIO/SPI/UART
●High-speed UART HCI, up to 4 Mbps
●Bluetooth 4.2 BR/EDR BLE dual mode controller
●Synchronous Connection-Oriented/Extended (SCO/eSCO)
●CVSD and SBC for audio codec
●Bluetooth Piconet and Scatternet
●Multi-connections in Classic BT and BLE
●Simultaneous advertising and scanning
■CPU and Memory:
●Xtensa®single-/dual-core 32-bit LX6 microprocessor(s), up to 600 MIPS (200 MIPS for ESP32-S0WD, 400MIPS for ESP32-D2WD)
●448 KB ROM
●520 KB SRAM
●16 KB SRAM in RTC
●QSPI supports multiple flash/SRAM chip
■Clocks and Timers:
●Internal 8 MHz oscillator with calibration
●Internal RC oscillator with calibration
●External 2 MHz~60 MHz crystal oscillator (40 MHz only for Wi-Fi/BT functionality)
●External 32 kHz crystal oscillator for RTC with calibration
●Two timer groups, including 2 × 64-bit timers and 1 × main watchdog in each group
●One RTC timer
●RTC watchdog
■Advanced Peripheral Interfaces:
●34 × programmable GPIOs
●12-bit SAR ADC up to 18 channels
●2 × 8-bit DAC
●10 × touch sensors
●4 × SPI
●2 × I²S
●2 × I²C
●3 × UART
●1 host (SD/eMMC/SDIO)
●1 slave (SDIO/SPI)
●Ethernet MAC interface with dedicated DMA and IEEE 1588 support
●CAN 2.0
●IR (TX/RX)
●Motor PWM
●LED PWM up to 16 channels
●Hall sensor
■Security:
●Secure boot
●Flash encryption
●1024-bit OTP, up to 768-bit for customers
●Cryptographic hardware acceleration:
◆AES
◆Hash (SHA-2)
◆RSA
◆ECC
◆Random Number Generator (RNG)
ESP32 is a single 2.4 GHz Wi-Fi-and-Bluetooth combo chip designed with the TSMC ultra-low-power 40 nm technology. It is designed to achieve the best power and RF performance, showing robustness, versatility and reliability in a wide variety of applications and power scenarios.
The ESP32 series of chips includes ESP32-D0WDQ6, ESP32-D0WD, ESP32-D2WD, and ESP32-S0WD. For details on part numbers and ordering information, please refer to Part Number and Ordering Information.
■Wi-Fi Key Features:
●802.11 b/g/n
●802.11 n (2.4 GHz), up to 150 Mbps
●WMM
●TX/RX A-MPDU, RX A-MSDU
●Immediate Block ACK
●Defragmentation
●Automatic Beacon monitoring (hardware TSF)
●4 × virtual Wi-Fi interfaces
●Simultaneous support for Infrastructure Station, SoftAP, and Promiscuous modes Note that when ESP32 is in Station mode, performing a scan, the SoftAP channel will be changed.
●Antenna diversity
■BT Key Features:
●Compliant with Bluetooth v4.2 BR/EDR and BLE specifications
●Class-1, class-2 and class-3 transmitter without external power amplifier
●Enhanced Power Control
●+12 dBm transmitting power
●NZIF receiver with –97 dBm BLE sensitivity
●Adaptive Frequency Hopping (AFH)
●Standard HCI based on SDIO/SPI/UART
●High-speed UART HCI, up to 4 Mbps
●Bluetooth 4.2 BR/EDR BLE dual mode controller
●Synchronous Connection-Oriented/Extended (SCO/eSCO)
●CVSD and SBC for audio codec
●Bluetooth Piconet and Scatternet
●Multi-connections in Classic BT and BLE
●Simultaneous advertising and scanning
■CPU and Memory:
●Xtensa®single-/dual-core 32-bit LX6 microprocessor(s), up to 600 MIPS (200 MIPS for ESP32-S0WD, 400MIPS for ESP32-D2WD)
●448 KB ROM
●520 KB SRAM
●16 KB SRAM in RTC
●QSPI supports multiple flash/SRAM chip
■Clocks and Timers:
●Internal 8 MHz oscillator with calibration
●Internal RC oscillator with calibration
●External 2 MHz~60 MHz crystal oscillator (40 MHz only for Wi-Fi/BT functionality)
●External 32 kHz crystal oscillator for RTC with calibration
●Two timer groups, including 2 × 64-bit timers and 1 × main watchdog in each group
●One RTC timer
●RTC watchdog
■Advanced Peripheral Interfaces:
●34 × programmable GPIOs
●12-bit SAR ADC up to 18 channels
●2 × 8-bit DAC
●10 × touch sensors
●4 × SPI
●2 × I²S
●2 × I²C
●3 × UART
●1 host (SD/eMMC/SDIO)
●1 slave (SDIO/SPI)
●Ethernet MAC interface with dedicated DMA and IEEE 1588 support
●CAN 2.0
●IR (TX/RX)
●Motor PWM
●LED PWM up to 16 channels
●Hall sensor
■Security:
●Secure boot
●Flash encryption
●1024-bit OTP, up to 768-bit for customers
●Cryptographic hardware acceleration:
◆AES
◆Hash (SHA-2)
◆RSA
◆ECC
◆Random Number Generator (RNG)
- +1 Like
- Add to Favorites
Recommend
More>
- How to Program 802.11bgn Wifi Module with ESP32 in RTOS?
- The Features and The Network Connection Method of ESP8266 WiFi Module
- OWON Has Demonstrated its XSA1000 Series, OWP-H, SPE Series, XDM Series in the 2023 Hong Kong Electronics Show
- Silicon Labs Announces Next Generation Series 3 Wireless Platform to Create a Smarter, More Efficient IoT
- Shindengen Adds JH Series and MG038 Series Large Capacity Three Phase Bridge Diodes
- ONPOW New Series- ONPOW61 Push Button Switch With Connector that Covers 16mm, 19mm, 22mm, and 25mm in Diameter
- Conductive Polymer Hybrid Aluminum Electrolytic Capacitors 80V products added to the HXA/HXB Series Radial lead type HSA/HSB Series commercialized
- Yangtze Microelectronics Introduces Integrated Inductors FTC Series and FEXL Series with a Thickness of 0.55mm
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.