JUMO digiLine Ci Intelligent electronics with RS485 interface for connecting inductive conductivity sensors to JUMO digiLine systems
■General:
▲The JUMO digiLine Ci in the version with an RS485 interface as a 5-pole M12 plug connector for connecting to a JUMO digiLine system. The device versions with an RS485 interface are used in the JUMO digiLine mode with plug & play support on the JUMO AQUIS touch S/P or in the Modbus mode on the JUMO mTRON T. Several sensors simultaneously transfer their measurement data to a master continuously over the JUMO digiLine bus.
■Installation and connection:
The JUMO digiLine Ci with RS485 interface is available in two device versions in terms of design type:
▲Device version as head transmitter:
JUMO digiLine electronics and sensor form an integrated module. The module is installed in a suitable fitting.
▲Device version with separate sensor:
JUMO digiLine electronics and sensor are separate mod-ules and are connected to one another by a cable. The sensor is installed in a suitable fitting. The JUMO digiLine electronics are mounted in the vicinity of the sensor using the supplied wall/pipe/DINrail holder.
If it becomes necessary to replace the sensor due to a defect or wear in the device version with a separate sensor, the JUMO digiLine electronics can be disconnected from the sensor and the intact components reused. In the device version as head transmitter, disconnecting the sensor from the JUMO digiLine electronics is not possible. The line and plug connectors of the JUMO digiLine Ci provide protection type IP69K to prevent problems caused by ingress of moisture.
Connecting to the bus is quick and easy by inserting and attaching a preassembled cable (available from JUMO).
■Configuration, parameterization and calibration:
The JUMO digiLine Ci with RS485 interface is normally configured, parameterized and calibrated via the operating panel on the JUMO AQUIS touch S/P. The calibration, however, also be conveniently carried out in the laboratory on a PC using the JUMO DSM-Software (Digital Sensor Management software). It is only necessary to connect the device to the PC via its USB interface.
|
JUMO digiLine Ci 、 202761 、 JUMO digiLine HT10 、 202761/10-10-8-01-10-168/000 、 202760 、 202760/10-10-8-01 |
|
|
User's Guide |
|
|
|
|
Please see the document for details |
|
|
|
|
|
|
|
|
|
|
|
English Chinese Chinese and English Japanese |
|
|
2020/03/30 |
|
|
V2.00 |
|
|
00691388 |
|
|
1.5 MB |
- +1 Like
- Add to Favorites
Recommend
- NetOps CI: Validating BGP-based DDoS Protection with Ixia-c and Containerlab
- Keysight Enhances Automated Software Test Solution to Enable Multi-Platform Mobile App Testing
- Exxelia is Proud to be Onboard Solar Orbiter which Carries More Than 16,000 of Passives
- Keysight Brings Keysight Open RAN Architect (KORA) to AWS Outposts
- The Micro Inductor Supplier, Guangzhou Jinkai Electronics (CHK) and Sekorm Announced a Distribution Agreement
- Silicon Labs Supports New Bluetooth® Mesh Feature Enhancements ＆ Networked Lighting Control Standardized Profiles
- Greenconn荣获邓白氏企业认证，实力彰显行业领先水平
- TeraSilIC‘s 24GHz mmWave radar sensor in smart washlets
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.
Integrated Circuits
Discrete Components
Connectors & Structural Components
Assembly UnitModules & Accessories
Power Supplies & Power Modules
Electronic Materials
Instrumentation & Test Kit
Electrical Tools & Materials
Mechatronics
Processing & Customization
