Integrated Isolated Power 3CH Digital Isolated Solution of NOVOSENSE for Both High Performance and Cost Effectiveness
In view of high voltage, safety, noise immunity, and other factors in industrial system design, the demand for isolated design is more and more extensive, and transferring signal/power across isolation barriers has been one of the common challenges for designers. As the leader of isolation technology, NOVOSENSE has been committed to exploring isolated power solutions with higher integration, reliability, and cost-effectiveness. This article introduces the integrated isolated power 3CH digital isolated solution of NOVOSENSE, which helps developers simplify industrial system design.
Isolated power supply solution based on an on-chip transformer
According to different requirements, the isolated power supply in the system can be divided into three parts: isolated drive power supply, isolated sampling power supply, and isolated communication power supply. Whereas, the power supply solution of external transformer /multi-winding output is adopted for the isolated drive/sampling power supply due to relatively large power and concentrated layout. For an isolated communication power supply, because its layout is relatively far away from the main power loop of the system and its power consumption is relatively low, the independent isolated power module is often preferred. With industry-leading on-chip transformer technology, the NIRSP31 integrates isolated power and three-channel digital isolators on a single chip with an advanced LGA package (4mm×5mm). Compared with the traditional isolated power module + optical coupler/digital isolator solution, it greatly reduces the PCB layout area and height, and can further reduce overall system cost.
*The parameters of the isolated power module in the preceding table are specific to a single part number, and the specifications vary with materials.
The above table compares the parameters of the NIRSP31 with those of the traditional isolated power module solution. In summary, the NIRSP31 has the following advantages:
Solution area reduction >200%
Solution cost reduction >15%
Flexible configuration, 5V/3.3V selectable output options
Excellent load regulation (integrated closed-loop control)
Wide operating temperature range (-40 °C to 125 °C), and low output power temperature derating
Enable (EN) pin for applications with low static power requirements
The small primary-secondary parasitic capacitance and high CMTI (common mode transient immunity)
Up to 3000Vrms 1-minute insulation voltage
Integrated short-circuit protection/over-temperature protection/under-voltage protection
Automatic packaging, high reliability, and low failure rate
High data rate and lifetime compared with the optocoupler
isolated power supply 3CH digital isolator NIRSP31 with high integration, high reliability, and high cost-effectiveness
Key parameters:
3kVrms insulation voltage
I/O voltage range supports 1.8~5.5V MCU
Supply voltage:
VDD: 4.5~5.5V for NIRSP31
3~3.6V/4.5~5.5V for NIRSP31VVDDL: 1.8~3.6V/4.5~5.5V
Output:
80mA @5V->5V/3.3V
60mA @3.3V->3.3V
Under-voltage protection, short-circuit protection, and over-temperature protection
Data rate: 20Mbps
Transmission delay: <75ns
CMTI: ±50kV/us
Operating temperature: -40~125℃
Package: LGA-18 (4.00mm × 5.00mm)
Applications:
E-Bike
Battery energy storage system
Industrial meter
Circuit breaker
Industrial BMS: NOVOSENSE total solution
In industrial BMS applications, NIRSP31 can be used in isolated RS485 and CAN communication between battery pack MCU and external ECUs without external isolated power supply and extra LDO (good load regulation) to ensure both compact design and system reliability.
Typical block diagram of industrial BMS
NOVOSENSE also provides a total solution for industrial BMS, including bidirectional I²C isolator NSI8100, RS485 transceiver NCA3485/NCA3491, CAN transceiver NCA1042/NCA1051, and dual-channel low-side driver NSD1025.
NIRSP31 Demo boards
Isolated RS485 communication Demo Board
isolated CAN communication demo board
For easy evaluation, NOVOSENSE provides isolated RS485 communication demo board NIRSP31+NCA3485 and isolated CAN communication demo board NIRSP31+NCA1042.
- +1 Like
- Add to Favorites
Recommend
- NOVOSENSE at PCIM Europe 2023: Semiconductor Solutions for Automotive & Industrial Applications
- NOVOSENSE Has Launched Multiple Automobile-qualified Chips with Breakthrough Innovation Technology In the first half of 2022!
- NOVOSENSE Assists the Formulation of LIN Transceiver Chip Standard, Promoting the High-quality Development of the Automotive Chip Industry
- NOVOSENSE Won VDE Premium Quality Award for High Quality Development
- NOVOSENSE Introduces the NSIP605x Series of Cost-Effective Push-Pull Transformer Drivers to Support Customers‘ Diverse and Flexible Designs
- NOVOSENSE Released a New 1200V Series SiC Diode with Typical Fowrard Voltage of 1.39V, Contributing to the SiC Ecosystem
- NOVOSENSE NST1002 Temperature Sensor Facilitates Accurate CGM Measurement with Glucose Monitoring Black Technology
- NOVOSENSE‘s New Isolation Voltage Sampling Chips NSI1312x Series Support +1.2V Bidirectional Linear Input Voltage
This document is provided by Sekorm Platform for VIP exclusive service. The copyright is owned by Sekorm. Without authorization, any medias, websites or individual are not allowed to reprint. When authorizing the reprint, the link of www.sekorm.com must be indicated.