RA2L1 Group Microcontrollers Datasheet

2021-05-18
● The MCU integrates multiple series of software- and pin-compatible Arm®-based 32-bit cores that share a common set of Renesas peripherals to facilitate design scalability.
The MCU in this series incorporates an energy-efficient Arm Cortex®-M23 32-bit core, that is particularly well suited for cost-sensitive and low-power applications, with the following features:
■ Up to 256-KB code flash memory
■ 32-KB SRAM
■ 12-bit A/D Converter (ADC12)
■ 12-bit D/A Converter (DAC12)
■ Security features
● Features:
■ Arm Cortex-M23 Core
▲ Armv8-M architecture
▲ Maximum operating frequency: 48 MHz
▲ Arm Memory Protection Unit (Arm MPU) with 8 regions
▲ Debug and Trace: DWT, FPB, CoreSight™ MTB-M23
▲ CoreSight Debug Port: SW-DP
■ Memory
▲ Up to 256-KB code flash memory
▲ 8-KB data flash memory (100,000 program/erase (P/E) cycles)
▲ 32 KB SRAM
▲ Memory protection units
▲ 128-bit unique ID
■ Connectivity
▲ Serial Communications Interface (SCI) × 5
◆ Asynchronous interfaces
◆ 8-bit clock synchronous interface
◆ Simple IIC
◆ Simple SPI
◆ Smart card interface
▲ Serial Peripheral Interface (SPI) × 2
▲ I²C bus interface (IIC) × 2
▲ CAN module (CAN)
■ Analog
▲ 12-bit A/D Converter (ADC12)
▲ 12-bit D/A Converter (DAC12)
▲ Low-Power Analog Comparator (ACMPLP) × 2
▲ Temperature Sensor (TSN)
■ Timers
▲ General PWM Timer 32-bit (GPT32) × 4
▲ General PWM Timer 16-bit (GPT16) × 6
▲ Low Power Asynchronous General Purpose Timer (AGT) × 2
▲ Watchdog Timer (WDT)
■ Safety
▲ ECC in SRAM
▲ SRAM parity error check
▲ Flash area protection
▲ ADC self-diagnosis function
▲ Clock Frequency Accuracy Measurement Circuit (CAC)
▲ Cyclic Redundancy Check (CRC) calculator
▲ Data Operation Circuit (DOC)
▲ Port Output Enable for GPT (POEG)
▲ Independent Watchdog Timer (IWDT)
▲ GPIO readback level detection
▲ Register write protection
▲ Main oscillator stop detection
▲ Illegal memory access
■ Security and Encryption
▲ AES128/256
▲ True Random Number Generator (TRNG)
■ System and Power Management
▲ Low power modes
▲ Switching regulator
▲ Realtime Clock (RTC)
▲ Event Link Controller (ELC)
▲ Data Transfer Controller (DTC)
▲ Key Interrupt Function (KINT)
▲ Power-on reset
▲ Low Voltage Detection (LVD) with voltage settings
■ Human Machine Interface (HMI)
▲ Capacitive Sensing Unit 2 (CTSU)
■ Multiple Clock Sources
▲ Main clock oscillator (MOSC) (1 to 20 MHz)
▲ Sub-clock oscillator (SOSC) (32.768 kHz)
▲ High-speed on-chip oscillator (HOCO) (24/32/48/64 MHz)
▲ Middle-speed on-chip oscillator (MOCO) (8 MHz)
▲ Low-speed on-chip oscillator (LOCO) (32.768 kHz)
▲ Clock trim function for HOCO/MOCO/LOCO
▲ IWDT-dedicated on-chip oscillator (15 kHz)
▲ Clock out support
■ Up to 85 pins for general I/O ports
▲ 5-V tolerance, open drain, input pull-up
■ Operating Voltage
▲ VCC: 1.6 to 5.5 V
■ Operating Temperature and Packages
▲ Ta = -40°C to +85°C
◆ 100-pin LQFP (14 mm × 14 mm, 0.5 mm pitch)
◆ 80-pin LQFP (12 mm × 12 mm, 0.5 mm pitch)
◆ 64-pin LQFP (10 mm × 10 mm, 0.5 mm pitch)
◆ 48-pin LFQFP (7 mm × 7 mm, 0.50 mm pitch)
◆ 48-pin HWQFN (7 mm × 7 mm, 0.50 mm pitch)
▲ Ta = -40°C to +105°C
◆ 100-pin LQFP (14 mm × 14 mm, 0.5 mm pitch)
◆ 80-pin LQFP (12 mm × 12 mm, 0.5 mm pitch)
◆ 64-pin LQFP (10 mm × 10 mm, 0.5 mm pitch)
◆ 48-pin LFQFP (7 mm × 7 mm, 0.50 mm pitch)
◆ 48-pin HWQFN (7 mm × 7 mm, 0.50 mm pitch)

Renesas

RA2L1 GroupRA2L1RA FamilyR7FA2L1AB3CFPR7FA2L1AB3CFNR7FA2L1AB3CFMR7FA2L1AB3CFLR7FA2L1AB3CNER7FA2L1AB2DFPR7FA2L1AB2DFNR7FA2L1AB2DFMR7FA2L1AB2DFLR7FA2L1AB2DNER7FA2L1A93CFPR7FA2L1A93CFNR7FA2L1A93CFMR7FA2L1A93CFLR7FA2L1A93CNER7FA2L1A92DFPR7FA2L1A92DFNR7FA2L1A92DFMR7FA2L1A92DFLR7FA2L1A92DNERA

More

Part#

MicrocontrollersMCU

More

More

Datasheet

More

More

Please see the document for details

More

More

100-pin LQFP;80-pin LQFP;64-pin LQFP;48-pin LFQFP;48-pin HWQFN

English Chinese Chinese and English Japanese

Aug 06, 2020

Rev. 1.00

R01DS0385EJ0100

4.6 MB

- The full preview is over. If you want to read the whole 110 page document,please Sign in/Register -
  • +1 Like
  • Add to Favorites

Recommend

All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.

Contact Us

Email: