A24C512 MEMORY EEPROM 512k BITS (65536 X 8) TWO-WIRE SERIAL
industrial standard 2-wire interface for
communications. The A24C512 contains a memory
array of 512k-bits (65,536x8), which is organized in
128-byte per page.
The EEPROM can operate in a wide voltage range
from 1.7V to 5.5V which fits most application. This
product can provide a low-power 2-wire EEPROM
solution.
The A24C512 is compatible with the industrial
standard 2-wire bus protocol. If in case the bus is not
responded, a new sent Op-code command will reset
the bus and the device will respond correctly. The
simple bus consists of the Serial Clock wire (SCL)
and the Serial Data wire (SDA).
Utilizing such bus protocol, a Master device, such as
a microcontroller, can usually control one or more
Slave devices, alike this A24C512.The bit stream
over the SDA line includes a series of bytes, which
identifies a particular Slave device, an instruction, an
address within that Slave device, and a series of
data, if appropriate. The A24C512 also has a Write
Protect pin (WP) to allow blocking any write
operations over specified memory area.
Under no circumstance, the device will be hung up.
In order to refrain the state machine entering into a
wrong state during power-up sequence or a power
toggle off-on condition, a power on reset circuit is
embedded. During power-up, the device does not
respond to any instructions until the supply voltage
(VCC) has reached an acceptable stable level above
the reset threshold voltage. Once VCC passes the
power on reset threshold, the device is reset and
enters into the Standby mode. This would also avoid
any inadvertent Write operations during power-up
stage.
During power-down process, the device will enter
into standby mode, once VCC drops below the power
on reset threshold voltage. In addition, the device will
be in standby mode after receiving the Stop
command, provided that no internal write operation
is in progress. Nevertheless, it is illegal to send a
command unless the VCC is within its operating level.
The A24C512 is available in SOP8, TSSOP8 and
DFN8 packages.
A24C512M8R 、 A24C512M8VR 、 A24C512TMX8R 、 A24C512TMX8VR 、 A24C512J8R 、 A24C512J8VR 、 A24C512 、 A24CXXX |
|
|
|
Datasheet |
|
Halogen free 、 RoHS |
|
Please see the document for details |
|
Industrial |
|
|
|
SOP8;TSSOP8;DFN8 |
|
English Chinese Chinese and English Japanese |
|
JAN 2017 |
|
REV1.1 |
|
|
|
939 KB |
- +1 Like
- Add to Favorites
Recommend
- 512Kbit I²C Compatible Serial EEPROM AiT A24C512 Requires a Single Power Supply in the Range of 1.7V to 5.5V
- AiT A6303 Series——300mA, Positive Voltage Output CMOS LDO Regulators
- AiT A7545 current mode boost DC-DC converter with Adjustable Output up to 9V and Internal Fixed PWM frequency of 1MHz
- AiT A713 DC-to-DC Step-down Switching Regulator with High Efficiency of up to 95%, ideal for Low-voltage Power Conversions
- AiT Offers Wide Range of Highly Precise SMD/TH Crystal Components in Half Size, Full Size, Cylindrical and Tuning Fork Packages
- AiT Offers Compact SMD Power Inductors Available in SMD Size Range from 0602 to 1812
- AiT offers 1A Linear Li-ion Batteries Charger IC A4051 for Single-cell Lithium-ion Batteries
- AiT‘s A7115B: a 1.5A, 2MHz High Efficiency Buck DC-DC Converter for Powering Portable Equipment
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.