Measures for Trouble in Li-ion Battery Protection Circuits

2023-05-18 NISSHINBO News
Li-ion Battery Protection Circuits,protection ICs,NISSHINBO

In this article, Nisshinbo would like to talk about troubles occurring in Li-ion Battery Protection Circuits. Thanks to its long experience in Li-ion battery protection circuits, NISSHINBO can provide protection ICs that give customers safety and security now. Reaching this level of service, however, required us to overcome a lot of difficulties, and we have developed and evolved our products every time we have been confronted with an array of problems. NISSHINBO will show you some examples and explain what kind of countermeasures are installed on protection ICs.


Measures against Electromagnetic Noise

One of the applications that brought up the Li-ion battery market largely is mobile phones. As a mobile phone sends and receives electromagnetic waves, its battery pack is always in an environment with electromagnetic noise. At the beginning of Li-ion batteries, this electromagnetic noise was a serious problem because it led to the misdetection of protection circuits.


An overcharge detection circuit did not have a delay circuit for detection and release at that time, and the output inverted in a short time of 20 to 30 µs after the inversion of the comparator for overcharge detection. In such a circuit, electromagnetic noise causes fluctuations of the reference voltage and voltage sense node input to the comparator, by which the output becomes inverted despite the battery voltage not reaching the overcharge detection voltage. As a result, the circuit turns to an overcharge detection state at a battery voltage close to its full capacity (but not fully charged), and the charging operation stops before the battery is fully charged. In addition, electromagnetic waves are emitted periodically from the mobile phone according to the communication method it adopts, so the output from the protection IC also oscillates periodically. In the worst case, the FET was damaged by the heat generated at certain frequencies. Through the experience of these failures, it has been common to set a delay time for each detection circuit inside a protection IC.


Without delay time for overcharge detection


With delay time for overcharge detection


The problem never ended only with false detection; false release also became problematic later. A battery pack detecting overcharge done by an abnormal charger stops charging operation even when a charger is connected, as a matter of course. However, there occurred a phenomenon that applying an electromagnetic wave to the battery pack at this state could restart the charging operation. This is just the opposite to false detection, namely, false release. Once such a phenomenon happens, the charging operation continues in spite of the overcharge being detected, the battery voltage rises beyond the overcharge detection voltage, and the battery falls into a dangerous situation due to being overcharged. To solve this problem, a delay time was also added to release from overcharge.


Without delay time for release from overcharge


With delayed time for release from overcharge


As mentioned above, contemporary protection ICs have as many countermeasures against noise as possible. The resistivity against electromagnetic noise, however, also depends on the layout of the protection circuit board. Long wiring for pins such as the VDD for voltage monitoring, and the V- and Rsense for current monitoring, will work as an antenna and make the board vulnerable to noise. Therefore, please locate external components as close to the protection IC as possible to shorten the wiring drawn in red in the following figure.



Measures against Reversely Connected Charger

Today’s mobile devices such as phones and laptop PCs contain a Li-ion battery which cannot be detached in many cases. In the past many Li-ion batteries used inside battery-powered applications were detachable. Securing safety considered, mechanical measures were taken to prevent the positive and negative terminals of a charger from being connected reversely. Nevertheless, we conducted evaluations for reverse connection to be ready at any chance.


The withstand voltage of our protection ICs is up to 30V. This value is derived from the battery voltage of 24V used in lorry trucks with some margins considered. The harshest condition of reverse charge testing adopted the application of reverse connection with 30V. If a FET with low withstands voltage is used, connecting a 30V reversely causes short and damage between the source and gate of the FET, which can lead to a dangerous situation of heat generation and firing. To prevent this, firstly, a protection diode is inserted between the source and gate of the FET to clamp the gate-source voltage with the Vf of the diode. In addition, a current limit resistor is necessary between the gate of the FET and the pin of the IC to stop a large current from flowing to the IC. These measures enable the protection circuit to avoid heat generation and firing even at reversely connected charging of 30V.


As mentioned above, many of Li-ion batteries used in today’s mobile devices are undetachable, and the charging terminal is covered by something. Although it is worth considering how much effort you will make to take measures against reverse connection, the circuit above will be informative if you have to consider the case where a charger is connected reversely.


Operation at Power-on

Although this is not trouble related to protection ICs, one of the important problems is the state of the protection IC at the power-on at the first connection of the protection circuit and the battery cell. We often receive inquiries about this problem from customers even today.


The operation of a protection IC at power-on depends largely on its specifications. Which specification matters most is the release type from the overdischarge state. There are roughly two types: auto-release type and latch type. The auto-release type determines its output simply by the battery voltage value. The output turns off at overdischarge in which the battery voltage falls below the overdischarge detection voltage and turns on at release from the overdischarge state when the battery voltage becomes higher than or equal to the overdischarge release voltage. On the other hand, as release conditions, the latch type requires not only that the battery voltage be higher than or equal to the release voltage but also that a charger be connected. This means that once overdischarge is detected, the latch type can never be released from the overdischarge state unless a charger is connected to the protection circuit regardless of the battery voltage reaching the release voltage.


Then, how does the difference between the two release types affect the operation at power-on? To begin with, the auto release type, when a battery cell is connected to the protection circuit for the first time, its output turns on at the battery cell voltage higher than or equal to the overdischarge release voltage. For example, the nominal cell voltage of 3.7 V can certainly turn on the output, and end-users can use the battery pack as soon as they receive it. On the other hand, once the latch-type protection IC powers on with an overdischarge detection state when connected to a battery, a charger is required to release the state. Therefore, users cannot use the battery unless they connect the battery to a charger.



Whether the IC powers on with an overdischarge state or not depends on the speed of the VDD voltage increase from the protection IC perspective. The protection IC turns to an overdischarge state by overdischarge remaining longer than the detection delay time. The delay time is configured by ICs; in the case of 20 ms, for instance, the latch-type IC will never power on with an overdischarge state if the VDD voltage rises from the minimum operating voltage to the overdischarge release voltage within 20 ms. As a result, the output starts on, and the battery pack is usable immediately.


The VDD voltage increase speed is the point to make a latch-type protection IC certainly start up with the output on. If you would like to do so, pay attention to connected components such as capacitors, as they are the cause of slowing down the speed.


To start up with output ON state using overdischarge release latch-type


In this volume, NISSHINBO introduced three cases that might be troubling for customers’ evaluation, but various know-how are necessary to make full use of Li-ion battery protection ICs. 


  • +1 Like
  • Add to Favorites

Recommend

This document is provided by Sekorm Platform for VIP exclusive service. The copyright is owned by Sekorm. Without authorization, any medias, websites or individual are not allowed to reprint. When authorizing the reprint, the link of www.sekorm.com must be indicated.

Contact Us

Email: