RS4T245-Q1 4-Bit Dual-Supply Bus Transceiver with Configurable Voltage Translation and 3-State Output
■This 4-bit non-inverting bus transceiver is a bidirectional voltage-level translator and can be used to establish digital switching compatibility between mixed-voltage systems. It uses two separate configurable power-supply rails, Both VCCA and VCCB supporting operating voltages from 1.65 V to 5.5 V, A ports, DIR and OE tracks the VCCA supply and B ports tracks the VCCB supply. This allows the support of both lower and higher logic signal levels while providing bidirectional translation capabilities between any of the 1.8V, 2.5V, 3.3V and 5.5V voltage nodes.
■The RS4T245-Q1 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input and the output-enable (OE) input activate either the B-port outputs or the A-port outputs or place both output ports into the high-impedance mode. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports is always active and must have a logic HIGH or LOW level applied to prevent excess ICC and ICCZ.
■This device is fully specified for partial-power-down applications using IOFF. The IOFF circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.
■The VCC isolation feature ensures that if either VCC input is at GND, all outputs are in the high-impedance state.
■To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor, the minimum value of the resistor is determined by the current-sinking capability of the driver.
■The RS4T245-Q1 is designed so that the control pins (DIR and OE ) are supplied by VCCA. It operates over an ambient temperature range of -40°C to +125°C.
●FEATURES
■Qualified for Automotive Applications
■AEC-Q100 Qualified with the Grade 1
■Control Inputs VIH/VIL Levels are Referenced to VCCA Voltage
■Power-Supply Range: VCCA and VCCB:1.65V to 5.5V
■VCC Isolation: If Either VCC is at GND, Both Ports are in the High-Impedance State
■IOFF: Supports Partial-Power-Down Mode Operation
■Extended Temperature: -40°C to +125°C
|
4-Bit Dual-Supply Bus Transceiver 、 4-bit non-inverting bus transceiver 、 bidirectional voltage-level translator |
|
|
[ Automotive Infotainment ][ Advance Driver Assistance Systems(ADAS) ][ Telematics ][ Navigation Systems ][ Cluster ] |
|
|
Datasheet |
|
|
|
|
Please see the document for details |
|
|
|
|
|
|
|
|
QFN2.5x3.5-16L |
|
|
English Chinese Chinese and English Japanese |
|
|
2023/06/06 |
|
|
REV A.1 |
|
|
|
|
|
1.3 MB |
- +1 Like
- Add to Favorites
Recommend
- Runic Technology Launches Eleven Automotive-qualified ICs Meeting AEC-Q100 Grade 1 and MSL1
- Jiangsu Runic Technology Won 2021 China Analog Semiconductor Outstanding Business Award
- Runic Technology Participates in the 2021 ASPENCORE Double Summit
- The RS3005 Chip Developed by Runic Technology Helped The System MCU to Complete The Power Supply
- Runic‘s OP Amp RS622，Analog Switch RS2105 and Low-Consumption LDO RS3236 Apply in Finger Clip Oximeter
- Runic OP Amp RS8551, LDO RS3002 and RS3226 Series Apply in Hand-Held Infrared Thermometer Detector
- Runic‘s OP Amp RS8538and RS622, Low-Consumption LDO RS3236 Apply in Electronic Blood-Pressure Meter
- Runic Low-power LDO RS3221 Assists in the Design of Smart Home Sensors and MCU Power Supply, With Small Package Size and Low Quiescent Current as Low as 1μA
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.
Integrated Circuits
Discrete Components
Connectors & Structural Components
Assembly UnitModules & Accessories
Power Supplies & Power Modules
Electronic Materials
Instrumentation & Test Kit
Electrical Tools & Materials
Mechatronics
Processing & Customization
