CPS Series MICRO SWITCH Cable-Pull Safety Switches Datasheet
2022-06-14
●DESCRIPTION
■Honeywell's MICRO SWITCH CPS Series Cable-Pull Safety Switches provide a readily accessible emergency stop signal, a cost-effective means compared to using multiple emergency stop push-buttons. The CPS Series Cable Pull Safety Switch’s internal mechanism latches on both slackened cable (push) and pulled cable.
■The 1CPS is intended for use in applications where the cable span is 76 m [250 ft] or shorter. It is an economical solution for shorter runs or zone protection typical to automated systems. The 2CPS Series is intended for use in very long cable runs of 152 m [500 ft] or shorter, such as long conveyor lines found in warehouses.
■A line in the midpoint of the cable tension window indicates proper cable tension, providing easy set-up. The direct opening switch contacts are held closed when the actuating cable is under proper tension and the reset knob is set to the RUN position. When the actuating cable is pulled, slackened, or broken, a cam positively opens the NC (Normally Closed) switch contacts. The snap-action operation causes the switch contacts to change state and mechanically latch almost simultaneously when the cable is pulled, slackened, or broken. The NC switch contacts remain open until the CPS is reset by properly tensioning the cable and manually rotating the reset knob.
■When the direct opening switch contacts open, the auxiliary contacts also actuate (open contacts close). The auxiliary contacts are electrically isolated from the direct-opening switch contacts. These NO (Normally Open) contacts may be used for monitoring or signaling.
●FEATURES
■Direct opening action of NC (Normally Closed) contacts
■2CPS: 2NO/2NC, 1NO/3NC, or 4NC contact configurations
■1CPS: 1NO/1NC, 2NO/2NC, 1NO/3NC, or 4NC contact configurations
■Typical cable span of 76 m [250 ft] in an environment with a temperature change of ±17 °C [±30 °F]. Longer spans are possible depending upon temperature change and installation
■Choice of three actuator configurations (2CPS)
■Removable contact block version available (2CPS)
■J-hook turnbuckle included (2CPS)
■E-stop option (1CPS)
■Low profile reset and new indicator options (2CPS)
■Large wiring cavity with straight-through wiring
■Models avaliable without broken cable, slack-cable detection
■24 Vdc or 120 Vac bright, multi-cluster high-intensity LED status indicator light available on 2CPS. Single LED on 1CPS. Low profile LED (2CPS) and emergency stop button (1CPS) options also offered
■Gold-plated contacts are standard on 2CPS, available on 1CPS
■Electrostatic, epoxy-coated, die-cast zinc housing
■Optional hardware packets available
■Honeywell's MICRO SWITCH CPS Series Cable-Pull Safety Switches provide a readily accessible emergency stop signal, a cost-effective means compared to using multiple emergency stop push-buttons. The CPS Series Cable Pull Safety Switch’s internal mechanism latches on both slackened cable (push) and pulled cable.
■The 1CPS is intended for use in applications where the cable span is 76 m [250 ft] or shorter. It is an economical solution for shorter runs or zone protection typical to automated systems. The 2CPS Series is intended for use in very long cable runs of 152 m [500 ft] or shorter, such as long conveyor lines found in warehouses.
■A line in the midpoint of the cable tension window indicates proper cable tension, providing easy set-up. The direct opening switch contacts are held closed when the actuating cable is under proper tension and the reset knob is set to the RUN position. When the actuating cable is pulled, slackened, or broken, a cam positively opens the NC (Normally Closed) switch contacts. The snap-action operation causes the switch contacts to change state and mechanically latch almost simultaneously when the cable is pulled, slackened, or broken. The NC switch contacts remain open until the CPS is reset by properly tensioning the cable and manually rotating the reset knob.
■When the direct opening switch contacts open, the auxiliary contacts also actuate (open contacts close). The auxiliary contacts are electrically isolated from the direct-opening switch contacts. These NO (Normally Open) contacts may be used for monitoring or signaling.
●FEATURES
■Direct opening action of NC (Normally Closed) contacts
■2CPS: 2NO/2NC, 1NO/3NC, or 4NC contact configurations
■1CPS: 1NO/1NC, 2NO/2NC, 1NO/3NC, or 4NC contact configurations
■Typical cable span of 76 m [250 ft] in an environment with a temperature change of ±17 °C [±30 °F]. Longer spans are possible depending upon temperature change and installation
■Choice of three actuator configurations (2CPS)
■Removable contact block version available (2CPS)
■J-hook turnbuckle included (2CPS)
■E-stop option (1CPS)
■Low profile reset and new indicator options (2CPS)
■Large wiring cavity with straight-through wiring
■Models avaliable without broken cable, slack-cable detection
■24 Vdc or 120 Vac bright, multi-cluster high-intensity LED status indicator light available on 2CPS. Single LED on 1CPS. Low profile LED (2CPS) and emergency stop button (1CPS) options also offered
■Gold-plated contacts are standard on 2CPS, available on 1CPS
■Electrostatic, epoxy-coated, die-cast zinc housing
■Optional hardware packets available
- +1 Like
- Add to Favorites
Recommend
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.
Integrated Circuits
Discrete Components
Connectors & Structural Components
Assembly UnitModules & Accessories
Power Supplies & Power Modules
Electronic Materials
Instrumentation & Test Kit
Electrical Tools & Materials
Mechatronics
Processing & Customization
