RF-WM-11AFB1 Ultra-Low-Power Wi-Fi Module
■RF-WM-11AFB1 is a PCB module based on Realtek Wi-Fi SoC RTL8711AF of Cortex™-M3 core at 83 MHz. This module has on-chip 512 KB RAM and 1 MB flash, a pin-out of peripherals of SDIO, SPI, UART, I2C, I2S, and GPIOs. It has integrated a 40 MHz crystal, an on-board PCB antenna, and an IPEX/U.FL connector for connecting to an external antenna. It supports 2.4 GHz 802.11 b/g/n at 20 MHz channel bandwidth with 75 Mbps maximum data rate. The module comes with a pre-programmed serial interface data communication protocol and an AT commands set to minimizes users’ effort to establish the data link to their existing MCUs or processors. It supports STA, AP, and STA + AP concurrent modes, advanced security features include Wi-Fi WEP, WPA, WPA2, and WPS2 with MD5, SHA-1, SHA2-256, DES, 3DES, and AES security engines
●Key Features:
■General
▲CMOS MAC, baseband PHY, and RF in a single chip for 802.11b/g/n compatible WLAN
▲Complete 802.11n solution for 2.4 GHz band
▲72.2 Mbps receive PHY rate and 72.2 Mbpstransmit PHY rate using 20 MHz bandwidth-150 Mbps receive PHY rate and 150 Mbpstransmit PHY rate using 40MHz bandwidth
▲Compatible with 802.11n specification
▲Backward compatible with 802.11b/g devices while operating in 802.11n mode
■Standards supported
▲802.11b/g/n compatible WLAN
▲802.11e QoS Enhancement (WMM)
▲ces-Wi-Fi WPS support
▲Wi-Fi direct support
▲Light weight TCP/IP protocol
■WLAN MAC features
▲Frame aggregation for increased MAC efficiency (A-MSDU, A-MPDU)
▲Low latency immediate High-Throughput Block Acknowledgement (HT-BA)
▲Long NAV for media reservation with CF-End for NAV release
▲PHY-level spoofing to enhance legacy compatibility
▲Power saving mechanism
■WLAN PHY features
▲802.11n OFDM
▲One Transmit and One Receive path (1T1R)
▲20 MHz and 40 MHz bandwidth transmission
▲Short guard interval (400 ns)
▲DSSS with DBPSK and DQPSK, CCKmodulation with long and short preamble
▲OFDM with BPSK, QPSK, 16QAM, and 640QAM modulation. Convolutional coding rate: 1/2, 2/3, 3/4, and 5/6
▲Maximum data rate 54 Mbps in 802.11g and 150 Mbps in 802.11n
▲Fast receiver Automation Gain Control (AGC)
▲On-chip ADC and DAC
■Peripheral interfaces
▲SDIO slave
▲Maximum 2 high speed UART interface with baud rate up to 4 MHz
▲1log UART with standard baud rate support
▲Maximum 3 I²C interface
▲I²S with 8/16/24/32/48/96/44.1/88.2KHz sampling rate
▲Maximum 2 PCM with 8/16 KHz sample rate
▲Maximum 2 SPI supported with baud rate up to 20.8 MHz
▲Support 4 PWM with configurable duration and suty cycle from 0 ~ 100%
▲Support 4 external timer trigger event (ETE function) with configurable period in low power mode
RF-WM-11AFB1 、 RF-WM-3200B1 、 RF-WM-3235B1 、 RF-WM-3220B1 、 RF-WM-3200B1I 、 RF-WM-3200B2 、 RF-WM-3200B3 、 RF-WM-10AFB1 、 CC3235SF 、 RTL8710AF 、 CC3235S 、 CC3220 、 RTL8711AF 、 CC3200 |
|
[ Cloud connectivity ][ Home automation ][ Home appliances ][ Access control ][ Security systems ][ Smart energy ][ Internet gateway ][ Industrial control ][ Smart plug ][ Smart metering ][ Wireless audio ][ IP network sensor nodes ] |
|
Datasheet |
|
|
|
Please see the document for details |
|
|
|
|
|
SMT |
|
English Chinese Chinese and English Japanese |
|
2020.01.19 |
|
V1.0 |
|
|
|
2.2 MB |
- +1 Like
- Add to Favorites
Recommend
- RF-STAR Launched RF-WM-3220B1,A Wi-Fi IoT Module Built on Basis of TI CC320SF IC
- RF-STAR RF-DG-40A Dongle——In-Depth Analysis of the Improvement of Nordic‘s Dongle Based on nRF52840
- RF-STAR’s New Modules Adopt NRF52833 Chip Will Come Soon
- RF-STAR Has Launched RF Modules Support Zigbee, BLE, Thread, and Other Multi-protocol Operations
- RF-STAR Launched The CC2640R2L Module With A Lower Cost And High Performance
- RF-DG-32A USB Sniffer Based on NRF52832 Chip Launched by RF-STAR , Which Supports Major Wireless Standards
- RF-STAR‘s Active Bluetooth IC Card Enables Gas Recharging at Home
- RF-star’s Development Kits of CC2340 BLE Modules Accelerate Projects
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.