FT2233HP/FT2232HP High Speed USB Bridge with Type-C/PD3.0 Controller Datasheet

PublishTime：2024-06-17

●The FT2233HP/FT2232HP is a Hi-Speed USB device with a Type-C/PD 3.0 controller that fully supports the latest USB Type-C and Power Delivery (PD) standards enabling support for power negotiation with the ability to sink or source current to a USB host device. The USB bridge function delivers 2 independent channels compatible with the existing FT2232H – Dual Hi-speed USB to multi-purpose UART/MPSSE solution.
●The FT2233HP/FT2232HP has the following advanced features:
■Supports the USBPD specification Rev 3.0
■Port 1 mode configuration for Sink or Dual Role Power
■Port 2 works as Sink, supporting charge through to port1 (FT2233HPQ only)
■Supports 5V3A, 9V3A, 12V3A, 15V3A and 20V3A PDOs as sink or source
■Supports up to 20 V/5 A (100 W) as a sink when attached to a PD source with 5 A certified type C cable
■Supports Fast Role Swap to switch from source to sink so that VBUS power will be uninterruptible
■Type-C/PD Physical Layer Protocol
■PD policy engine using 32-bit RISC controller with 8 kB data RAM and 48 kB code ROM
■PD mode configuration through external EEPROM
■Options to use external MCU controlling PD policy through I²C interface
■USB to dual serial ports with a variety of configurations
■USB to dual FIFO ports available in Asynchronous FIFO mode, or one USB to Synchronous FIFO port. Enabled by external EEPROM settings
■USB to parallel FIFO transfer data rate up to 8 Mbytes/s
■Single channel synchronous FIFO mode for transfer up to 40 Mbytes/s
■Entire USB protocol handled on the chip. No USB specific firmware programming required
■USB 2.0 High Speed (480 Mbits/s) and Full Speed (12 Mbits/s) compatible
■Two Multi-Protocol Synchronous Serial Engine (MPSSE) on channel A and channel B, to simplify synchronous serial protocol (USB to JTAG, I²C, SPI or bit-bang) design
■Independent Baud rate generators
■RS232/RS422/RS485 UART Transfer Data Rate up to 12 Mbaud. (RS232 Data Rate limited by external level shifter)
■FTDI’s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases
■CPU-style FIFO interface mode simplifies CPU interface design
■Fast Opto-Isolated serial interface option
■MCU host bus emulation mode configuration option
■Optional traffic TX/RX indicators can be added with LEDs
■Adjustable receive buffer timeout
■Support for USB suspend and resume conditions via PWREN#, SUSPEND# and RI# pins
■FTDI FT232R/FT-X style, asynchronous serial UART interface option with full hardware handshaking and modem interface signals
■Fully assisted hardware or X-On / X-Off software handshaking
■UART Interface supports 7/8-bit data, ½ stop bits, and Odd/Even/Mark/Space/No Parity
■Auto-transmit enable control for RS485 serial applications using TXDEN pin
■Operational configuration mode and USB Description strings configurable in external EEPROM over the USB interface
■Low operating and USB suspend current
■UHCI/OCHI/EHCI host controller compatible
■Configurable I/O drive strength (4, 8, 12 or 16 mA) and slew rate
■USB Bulk data transfer mode (512-byte packets in High-Speed mode)
■Dedicated Windows/Linux DLLs available for USB to SPI, and USB to I²C applications
■+3.3 V single supply operating voltage range
■+1.2 V (chip core) and +3.3 V I/O interfacing (+5 V Tolerant)
■Highly integrated design includes +1.2 V LDO regulator for VCORE, integrated POR function and on chip clock multiplier PLL (12 MHz – 480 MHz)
■Extended -40°C to 85°C industrial operating temperature range
■Available in Pb-free QFN-76/QFN-68package (RoHS compliant)

Brand of Product：	FTDI CHIP
Part#：	FT2233HP 、 FT2232HP 、 FT2232HQ 、 FT2232HL 、 FT2232H 、 FT2233HPQ 、 FT232 、 FT245 、 FT2232HPQ More Part#
Product Category：	High Speed USB Bridge 、 Hi-Speed USB device More
Application：	[ USB Smart Card Readers ][ USB Instrumentation ][ USB Industrial Control ][ USB FLASH Card Reader / Writers ][ Set Top Box PC – USB interface ][ USB Digital Camera Interface ][ USB Bar Code Readers ] More
Data Type：	Datasheet More
Safety & Environment Standards：	More
Operating Temperature：	Please see the document for details
Qualification Grade：	More
Qualification Approval：	More
Package：	QFN 64;LQFP 64
Language：	English Chinese Chinese and English Japanese
Date of Creation：	05-04-2024
Version Number：	Revision 1.5
Data Encoding：	FT_001474
Data Size：	4.9 MB

Data section preview(2pages)

- The full preview is over. If you want to read the whole 56 page document,please Sign in/Register -

Download

+1 Like
Add to Favorites

Recommend

New Products & Solutions

More>

Technical Resources

More>

All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.

Integrated Circuits