Honeycomb Vent Panels
●Think Schlegel EMI for Shielding
■As the originator of the fabric-clad foam EMI shielding technology, Schlegel EMI is the industry's most trusted name. Schlegel continues to set the standard for quality and innovation, designing advanced solutions for a wide range of applications.
■Modern electronic equipment often requires EMI Gaskets to avoid radiating EMI/RFI suspeptibility to outside sources of EMI/RFI. Maintaining electromagnetic compatibility can be an increasing challenge of the designers of today's electronic and electrical products.
■How do Honeycomb vents work:
▲The principle is that of "Waveguide beyond cutoff". The honeycomb vent is series of tubes that acts as a waveguide, guiding electromagnetic waves into or out of the enclosure, but as the tubes are long enough then it attenuates those waves. Typically the tube should be at least 3 times as long as the diameter. Good practice is 4 times. Therefore a 3.18mm cell should be 12.7mm long. Honeycomb material is used because it offers high shielding performance, light weight and good airflow.
■Schlegel uses 5052 grade aluminium foil which is a lightweight material offering superior strength and corrosion resistance over commercial grade aluminium foils. It meets all the requirements of MIL-C- 7438. This material is used to manufacture aircraft floors & wing edges, missile wings, helicopter rotor blades etc, so quality and repeatability is assured. Currently Schlegel has 7 frame styles available. To keep down production cost, vent panels made with styles 1701, 1703, 1705, 1706 & 1707 are normally supplied with 3 corners notched and the 4th joined corner welded. If required, all 4 corners of the panel can be supplied fully welded. Frame styles 1702 & 1704 are always supplied with fully welded corners.
■All frame styles are supplied with a conductive gasket to provide the best electrical contact between the frame and mating metal surface.
■Standard tolerances for overall Finished Vent Dimensions are +/- 0.8mm
■Standard tolerances on Hole Centres are +/- 0.4mm
■Typical corner radii on frame styles 1701,1703, 1705, 1706 & R3.0mm
■The standard finish for aluminium vent panels is SemPas , it fully meets the RoHS directive and replaces Alocrom 1200. This in-house process applies a permanganate passivation which is a chromate free, inorganic and non toxic coating. The process produces a dense, uniform coating consisting of aluminium and reduced manganese oxides giving a golden yellow colour to the surface. The surface finish is conductive with a low contact resistance equalling Alocrom 1200. It also meets all requirements of MIL-C-5541E for corrosion and electrical conductivity
Selection catalogue
1702 、 1703 、 1701 、 1705 、 1706 、 1704 、 TYPE 1707 、 1707 、 TYPE 1702 、 TYPE 1709 、 1709 、 TYPE 1708 、 1708 、 Type 1 、 Type 2 、 Type 3 、 Type 4 、 Type 5 、 Type 6 、 TYPE 1703 、 TYPE 1704 、 TYPE 1705 、 Schlegvent40 、 Schlegvent60 、 Schlegvent80 、 Schlegvent92 、 Schlegvent120 、 1721 、 1722 |
|
Honeycomb Vent Panels 、 Aluminium Honeycomb Air Ventilation Panels 、 Combined EMC and Dust Filter Ventilation Panels 、 Ventilation panels 、 Aluminium Screen EMC and Dust Filter Ventilation Panels |
|
[ aircraft floors ][ wing edges ][ missile wings ][ helicopter rotor blades ][ electronic enclosures ][ Air Conditioning Units ][ Fan housings ][ EMC Racks ][ commercial electronic enclosures ][ commercial ] |
|
Selection guide |
|
|
|
Please see the document for details |
|
|
|
|
|
|
|
English Chinese Chinese and English Japanese |
|
06/2019 |
|
|
|
|
|
3.4 MB |
- +1 Like
- Add to Favorites
Recommend
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.