MKP DC B25620 Film Capacitors - Power Electronic Capacitors
2022-09-29
●Characteristics
■Standard capacitance tolerance K: ±10%
■Dielectric dissipation factor (tan δo): 2 • 10-4
■Service life expectancy(refer to section 3)
▲100 000 h at Ths +75 °C and VRDC
▲up to 200 000 h (Considering de-ratings in voltage and/or temperature (upon request))
■Expected fit rate αFQ (co): 50 fit at VRDC and 70 °C (refer to section 4)
■Minimum temperature Top, min.: –55 °C
■Maximum temperature Top, max.
▲+85 °C for diameter 85 mm
▲+75 °C for diameter 116 mm
■Storage temperature Tstg: –55 ... +85 °C
■Maximum hotspot temperature Ths(refer to section 1)
▲+85 °C for diameter 85 mm
▲+75 °C for diameter 116 mm
■Climatic category
▲55/85/56 for 85 mm diameter
▲55/75/56 for 116 mm diameter
■Maximum altitude: 2000 m above sea level(derating curves for altitudes higher than 2000 m available upon request)
■Frequency range
▲100 Hz to 10 kHz for CR ≤ 1500 μF
▲100 Hz to 5 kHz for 1500 μF < CR ≤ 3000 μF
▲100 Hz to 3 kHz for 3000 μF< CR ≤ 4000 μF
▲(High frequency designs available upon request)
■Safety device: No internal protection
●Test data
■Voltage between terminals VTT: 1.5 VRDC, 10 s
■Voltage between terminals and case VTC: 4000 Vac,10 s
●Design data
■Resin filling: Non PCB, hard polyurethane (dry type)
■Mounting and grounding: M12 threaded bolt on bottom of the aluminum case
■Max. torque (case) M12 stud: 10 Nm
■Max. torque terminal
▲Female M6: 5 Nm
▲Female M8: 6 Nm
▲Male M8: 8 Nm
■Cooling: Naturally air-cooled (or forced air cooling)
■Degree of protection: IP00 (Indoor mounting)
■Standard capacitance tolerance K: ±10%
■Dielectric dissipation factor (tan δo): 2 • 10-4
■Service life expectancy(refer to section 3)
▲100 000 h at Ths +75 °C and VRDC
▲up to 200 000 h (Considering de-ratings in voltage and/or temperature (upon request))
■Expected fit rate αFQ (co): 50 fit at VRDC and 70 °C (refer to section 4)
■Minimum temperature Top, min.: –55 °C
■Maximum temperature Top, max.
▲+85 °C for diameter 85 mm
▲+75 °C for diameter 116 mm
■Storage temperature Tstg: –55 ... +85 °C
■Maximum hotspot temperature Ths(refer to section 1)
▲+85 °C for diameter 85 mm
▲+75 °C for diameter 116 mm
■Climatic category
▲55/85/56 for 85 mm diameter
▲55/75/56 for 116 mm diameter
■Maximum altitude: 2000 m above sea level(derating curves for altitudes higher than 2000 m available upon request)
■Frequency range
▲100 Hz to 10 kHz for CR ≤ 1500 μF
▲100 Hz to 5 kHz for 1500 μF < CR ≤ 3000 μF
▲100 Hz to 3 kHz for 3000 μF< CR ≤ 4000 μF
▲(High frequency designs available upon request)
■Safety device: No internal protection
●Test data
■Voltage between terminals VTT: 1.5 VRDC, 10 s
■Voltage between terminals and case VTC: 4000 Vac,10 s
●Design data
■Resin filling: Non PCB, hard polyurethane (dry type)
■Mounting and grounding: M12 threaded bolt on bottom of the aluminum case
■Max. torque (case) M12 stud: 10 Nm
■Max. torque terminal
▲Female M6: 5 Nm
▲Female M8: 6 Nm
▲Male M8: 8 Nm
■Cooling: Naturally air-cooled (or forced air cooling)
■Degree of protection: IP00 (Indoor mounting)
- The full preview is over,the data is 2 pages -
- +1 Like
- Add to Favorites
Recommend
More>
- TDK Shakes Up Robotics Market with Next-generation SmartRobotics™ Platform, TDK RoboKit1
- TDK Redefines True Wireless Stereo Applications With Vibesense360™ TWS Solution Suite
- TDK Worldwide Availability of The Industry’s First 7-Axis Motion and Pressure Sensor ICM-2078 Targeting The Consumer Electronic, Drone, and IOT Markets
- TDK Announces Thermally Stable Industrial IMU for Tilt and Stabilization Applications
- TDK Extends Battery Life of Kaadas Smart Door Lock with SmartSonic™ Ultra-low-power Time-of-Flight Sensors CH201
- TDK Provides MEMS Microphone Solutions for Expanding the Possibilities of Interactive Robots
- TDK announces SmartBug™ 2.0 – A Smarter Digital Transformation Module, Now with Machine Learning Enabled ICM-45686-S IMU
- TDK Launches Three New SmartSound™ MEMS Microphones Compatible with Sn/Pb and Pb-free Solder Processes
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.