PS1000-D2-24.10 0 Installation Manul

PublishTime：2022-01-10

●Product Description:
The PS1000-D2-24.10 is a DIN-rail mountable DC/DC converter, which provides a floating, stabilized and galvanically separated SELV/PELV output voltage.
●Intended Use:
■This device is designed for installation in an enclosure and is intended for commercial use, such as in industrial control, process control, monitoring, measurement equipment or the like.
■Do not use this device in equipment, where malfunctioning may cause severe personal injury or threaten human life without additional appropriate safety devices, that are suited for the end-application.
■If this device is used in a manner outside of its specification, the protection provided by the device may be impaired.
●Installation Instructions:
■Install device in an enclosure providing protection against electrical, mechanical and fire hazards. Install the device onto a DIN-rail according to EN 60715 with the input terminals on the bottom of the device. Other mounting orientations require a reduction in output current.
■Make sure that the wiring is correct by following all local and national codes. Use appropriate copper cables that are designed for a minimum operating temperature of 60°C for ambient temperatures up to +45°C, 75°C for ambient temperatures up to +60°C and 90°C for ambient temperatures up to +70°C. Ensure that all strands of a stranded wire enter the terminal connection. Unused screw terminals should be securely tightened.
■The device is designed for pollution degree 2 areas in controlled environments. No condensation or frost is allowed.
■The enclosure of the device provides a degree of protection of IP20. The enclosure does not provide protection against spilled liquids.
■The input can be powered from batteries or similar DC sources. The voltage between the input terminals and ground must not exceed 60Vdc continuously.
■The input must be powered from a PELV or SELV source or an "Isolated Secondary Circuit" in order to maintain a SELV or PELV output.
■Check for correct input polarity. The device will not operate when the voltage is reversed. A disconnecting means shall be provided for the input of the device.
■The device is designed as “Class of Protection I” equipment according to IEC 61140. Do not use without a proper PE (Protective Earth) connection.
■The device is designed for convection cooling and does not require an external fan. Do not obstruct airflow and do not cover ventilation grid!
■The device is designed for altitudes up to 5000m (16400ft). Above 2000m (6560ft) a reduction in output current is required.
■Keep the following minimum installation clearances: 40mm on top, 20mm on the bottom, 5mm left and right side. Increase the 5mm to 15mm in case the adjacent device is a heat source. When the device is permanently loaded with less than 50%, the 5mm can be reduced to zero.
■The device is designed, tested and approved for branch circuits up to 50A without additional protection device. If an external fuse is utilized, do not use circuit breakers smaller than 20A B- or C-Characteristic to avoid a nuisance tripping of the circuit breaker.
■The maximum surrounding air temperature is +70°C (+158°F). The operational temperature is the same as the ambient or surrounding air temperature and is defined 2cm below the device.
■The device is designed to operate in areas between 5% and 95% relative humidity.
●Functional Description:
■The output is electronically protected against no-load, overload and short circuit and can supply any kind of loads, including unlimited inductive and capacitive loads.
■Do not apply return voltages from the load to the output terminals higher than 35V.
■The output voltage can be adjusted with a small flat-blade screwdriver on the front of the unit.
■The green DC OK LED reports a voltage on the output terminals above 21Vdc.
■Devices can be paralleled to increase the output power. The ambient temperature is not allowed to exceed +45°C. The output voltage shall be adjusted to the same value (±100mV) with the same load conditions on all devices, or the devices can be left with the factory settings. If more than three devices are connected in parallel, a diode, fuse or circuit breaker with a rating of 15A or 16A is required on each output.
■Same devices can be connected in series for higher output voltages. It is allowed to connect as many devices in series as needed, providing the sum of the output voltage does not exceed 150Vdc.
■In case of an internal defect, a redundant circuit limits the maximum output voltage to 32.5V. The output shuts down and automatically attempts to restart.

Brand of Product：	Pepperl+Fuchs
Part#：	PS1000-D2-24.10 More Part#
Product Category：	DC/DC converter More
Application：	More
Data Type：	User's Guide More
Safety & Environment Standards：	More
Operating Temperature：	Please see the document for details
Qualification Grade：	More
Qualification Approval：	More
Package：
Language：	English Chinese Chinese and English Japanese
Date of Creation：	2020-08-23
Version Number：
Data Encoding：	PU-421.015.27-xxZ
Data Size：	45 KB

Data section preview(2pages)

- The full preview is over,the data is 2 pages -

Download

+1 Like
Add to Favorites

Recommend

New Products & Solutions

More>

Technical Resources

More>

All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.

Integrated Circuits