CAM-M8 series Omni-directional u-blox M8 GNSS antenna modules
■The u-blox CAM-M8 series antenna modules are built on the exceptional performance of the u-blox M8 GNSS engine. The CAM-M8 modules utilize concurrent reception of up to three GNSS systems (GPS/Galileo together with either BeiDou or GLONASS), offering high sensitivity and strong signal levels in an ultra compact form factor.
■Incorporating the CAM-M8 series modules into customer de-signs is simple and straightforward, thanks to the embedded GNSS antenna, small footprint of 9.6 x 14 x 1.95 mm, and so-phisticated interference suppression that ensures maximum performance even in GNSS-hostile environments. The low power consumption and thin design allow end devices to be slimmer and smaller. The CAM-M8 modules also support mes-sage integrity protection, geofencing, and spoofing detection.Despite their miniature size, the chip antennas in the CAM-M8 series modules perform extremely well against traditional patch antennas. Optimal performance is achieved by following design instructions available in the Hardware Integration Manual as the customer PCB is part of the anten-na solution. The omnidirectional radiation pattern increases flexibility for device installation. Optionally, CAMM8 series modules can be connected to an external GNSS antenna. The SMD design keeps manufacturing costs to a minimum and the small mass ensures high reliability.
■The CAM-M8 modules target industrial and consumer applications that require concurrent GPS/Galileo and GLONASS or GPS/Galileo and BeiDou reception. The CAM-M8C is optimized for cost-sensitive applications and has the lowest power consumption, while the CAM-M8Q provides best performance. The CAM-M8 modules are form-factor compatible with the UC530 and UC530M modules, allowing the upgrade of existing designs with minimal effort.
■CAMM8 modules use GNSS chips qualified according to AEC Q100 and are manufactured in ISO/TS 16949 certified sites. Qualification tests are performed as stipulated in the ISO16750 standard: “Road vehicles – Environmental conditions and testing for electrical and electronic equipment”.
CAM-M8 series 、 CAM-M8 、 CAM-M8Q 、 CAM-M8C 、 EVK-M8QCAM 、 EVK-M8CCAM |
|
|
|
Datasheet |
|
|
|
Please see the document for details |
|
|
|
|
|
LCC |
|
English Chinese Chinese and English Japanese |
|
2018 |
|
R05 |
|
UBX-16015855 |
|
170 KB |
- +1 Like
- Add to Favorites
Recommend
- Taoglas and u-blox Partner to Deliver Highly Reliable Positioning Solution for E-Bike Provider COWBOY
- OWON Has Demonstrated its XSA1000 Series, OWP-H, SPE Series, XDM Series in the 2023 Hong Kong Electronics Show
- Silicon Labs Announces Next Generation Series 3 Wireless Platform to Create a Smarter, More Efficient IoT
- Shindengen Adds JH Series and MG038 Series Large Capacity Three Phase Bridge Diodes
- ONPOW New Series- ONPOW61 Push Button Switch With Connector that Covers 16mm, 19mm, 22mm, and 25mm in Diameter
- Conductive Polymer Hybrid Aluminum Electrolytic Capacitors 80V products added to the HXA/HXB Series Radial lead type HSA/HSB Series commercialized
- Yangtze Microelectronics Introduces Integrated Inductors FTC Series and FEXL Series with a Thickness of 0.55mm
- Nippon Chemi-Con Developed Snap-in Type Aluminum Electrolytic Capacitors RLB Series with High Ripple and RLA Series with Longer Life
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.