EMB-4924 motherboard
●Size
◆Size:165mmX115mm
●Processor
◆CPU：Intel Ivy(Sandy)Bridge processors
●Chipset
◆Chipset：Intel HM76
●System Memory
◆System memory：1x single channel SO-DIMM memory slot, support DDRIII 1066/1333/1600Mhz，do not support ECC function，memory up to 4GB.
●Display
◆Display port：LVDS，VGA
◆Display combination：VGA+LVDS
◆LVDS：one 2x20Pin 2.0mm dual channel 24bit LVDS pin port，supports maximum resolution: 1920x1200@60Hz
◆VGA：one 2x5Pin 2.0mm pin port，supports maximum resolution: 2048x1536@75Hz
Note:When using more than +12V power supply, it is necessary to pay attention to the maximum voltage supported by LVDS screen.If you have any questions,please contact NORCO technician.
●Ethernet
◆Network controller：with PCIe port chip，Model: RTL8111F
◆Rate：10/100/1000Mbps
◆Support Wake On LAN（WOL）
Storage
◆Support SATAII/SATAIII；
◆Provide 2x standard 7Pin SATA port；
◆Independent power socket（5Pin connector）
Note:when the power supply is more than +12V, the 5pin power supply socket can not connect the hard disk powered by+12V. If you have any questions, please contact NORCO technician.
●AUDIO
◆Adopt ALC662 audio control chip，support Line-out、Line-in、Mic-in and power amplifier function；
◆Port：Provide one 2x5Pin 2.0mm audio pin and 1x 4Pin 2.0mm power amplifier pin
●I/O
◆I/O chip：IT8783
◆Serial port：Provide one 2x20Pin 2.0mm COM1_4 serial port pin，support RS232 model；
●USB
◆Provide 10x USB2.0 port，2x standard USB3.0 rear port，4x2x5Pin 2.0mm USB2.0 pin，can be transferred to 8x standard USB2.0 port.
Note:the[xHCI mode] option in BIOS is set to[Smart Auto]by
default.When using USB3.0 port, USB device may not be detected in DOS or BIOS interface some times.At this time,you need to change the[xHCI Mode]option to[Enable]setting,but you cannot install XP system after changing to[Enable].XP system can be installed by default when[Smart Auto].
●KBMS
◆1x 2x4Pin 2.0mm mouse and key board pin，the standard PS/2 key board and mouse interface can be output with the adapter cable
●Expansion Interface
◆3x standard MINI PCIE port，all support standard MINI PCIE module. 1x support 3G module by default、1x support MSATA SSD module by default（EPC SDD are optional）、1x support standard MINI PCIE module by default.
●Power supply
◆2Pin single power supply；
◆Support+12V~+19V power supply；
◆Support +12V battery-powered，it supports the battery charging function.When charging the battery,the external power supply required is+19v
●Watchdog
◆Support hardware reset
●BIOS
◆BIOS：8MB SPIF LASH
●Operating Environment
◆Operating Temperature：0℃～60℃
◆Storage Temperature：-40℃～85℃
◆Operating Humidity：5%~95%，non-condensing
|
|
|
|
User's Guide |
|
|
|
|
Please see the document for details |
|
|
|
|
|
|
|
|
|
|
|
English Chinese Chinese and English Japanese |
|
|
2021/03/31 |
|
|
V1.2 |
|
|
|
|
|
3.4 MB |
- +1 Like
- Add to Favorites
Recommend
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.
Integrated Circuits
Discrete Components
Connectors & Structural Components
Assembly UnitModules & Accessories
Power Supplies & Power Modules
Electronic Materials
Instrumentation & Test Kit
Electrical Tools & Materials
Mechatronics
Processing & Customization
