STEVAL-ESC001V1 Electronic speed controller reference design for drones Data brief
●Description
■The STEVAL-ESC001V1 reference design for electronic speed controllers (ESC) for drones fits entry-level commercial drone designs and drives any three-phase brushless (or PMSM) motor running off 6S LiPo battery packs, or any equivalent DC supply, up to 30 A peak current.
■The STEVAL-ESC001V1 lets you spin a motor and its propeller in minutes thanks toa complete pre-configured firmware package (STSW-ESC001V1), implementing a sensorless Field Oriented Controlled algorithm with 3-shunt current reading, speed control and full active braking.
■The reference design board can accept commands from a flight control unit through PWM signals; other communication bus interfaces like UART, CAN, and I²C are also available. The reference embeds a battery eliminator circuit working at 5 V, an NTC sensor for temperature measurement and circuitry for overcurrent/overvoltage protection (OCP/OVP). The compact form factor and current capability render this reference design suitable for electronic speed controllers on small and light unmanned aerial vehicles like professional drones.
■The STSW-ESC001V1 firmware/software package plus STM32 PMSM FOC software development kit - MC library let you refine your electronic speed controller design by acting on the field oriented control parameters embedded in the STM32 and experiment with the ST motor profiler to rapidly retrieve the motor parameters. The ST sensorless FOC algorithm ensures longer flight times and optimal dynamic performance.
■The STEVAL-ESC001V1 has been designed around the highly efficient, low R-dson STripFET F7 power MOSFETs, the high-performance STM32F303CBT7microcontroller with ARM® Cortex®-M4 core and the L6398 drivers.
●Features
■Complete reference design for electronic speed controller implementing a sensorless FOC algorithm
■Designed for drones with 6S pack of LiPo batteries or systems with an equivalent suitable DC supply
■ESC ready for communication with any standard flight control unit (FCU): PWM or CAN
■Temperature overheating protection
■Nominal operating voltage range: 3S-6S Li-Po battery DC voltage level (11.1 to22.2 V)
■Maximum RMS output current: 20 Arms
■Output peak current: 30 A
■Battery eliminator circuit (BEC): 5 V/0.5 A for external receiver or FCU
■Complete pre-configured firmware package available (STSW-ESC001V1)
■Supported by ST motor control software SDK and ST motor profiler
■Compact PCB design: 29.1 x 58 mm
■Further target applications:
▲motor driving for RC vehicles: electric cars, helicopter, trucks, etc.
▲any three-phase BLDC or PMSM motor application
■RoHS and WEEE compliant
STEVAL-ESC001V1 、 STSW-ESC001V1 、 STM32F303CBT7 、 STL160N4F7 、 L6398 、 STM32 、 STripFET F7 |
|
Datasheet |
|
|
|
Please see the document for details |
|
|
|
|
|
|
|
English Chinese Chinese and English Japanese |
|
November 2018 |
|
Rev 3 |
|
DB3230 |
|
919 KB |
- +1 Like
- Add to Favorites
Recommend
- Rosenberger and STMicroelectronics Cooperate to Develop a Unique High-Speed Contactless Connector Based on 60GHz Wireless Technology
- MTA Announces Partnership with STMicroelectronics for Smart Tractor
- STMicroelectronics and Sierra Wireless Collaborate to Simplify and Accelerate Connected IoT Solutions Deployment
- Eclipse Global Connectivity, Smiths Interconnect and ST Engineering IDirect Collaborate to Deliver a New Airborne ISR SATCOM Capability
- ROHM Group Company SiCrystal and STMicroelectronics Expand Silicon Carbide Wafer Supply Agreement
- China Requires Automobile Manufacturers to Increase the Proportion of Domestic Chip Procurement
- Rosenberger‘s Innovative Contactless Connector RoProxCon can Bridge Construction-related Air Gaps and Has A High Interference Immunity
- New High Side Switch ICs with User-Definable Protection Achieve Optimized Performance in Automotive Applications
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.