U2000 Series USB Power Sensors DATA SHEET
Compact “power meters”, simple set-up:
The U2000 Series are standalone sensors. That means they essentially operate like power meters, just in smaller forms. No reference calibrator is required. The fact that each sensor draws minimal power from a USB port—and that it doesn’t need additional triggering modules or power adaptors to operate—makes it more portable, especially for base station testing. Setting up is easy: just plug it to the USB port of your PC or laptop—or even select network or handheld spectrum analyzer—and start your power measurements. The figure below illustrates the very simple, straightforward setup of the U2000 Series.
High accuracy:
Each U2000 Series sensor provides excellent linearity, SWR and uncertainty specifications, so you can be confident in every measurement you make.
Wide range, high power:
The U2000 Series’ dynamic range spans across a wide 80 dB, taking on high power up to +44 dBm.
Remote monitoring and tests:
With the U2000 Series sensor plugged to a networked USB hub, you can conveniently monitor power measurements of an antenna tower from the control room, beyond the limits of USB cable lengths.
Faster production testing of multiple channels:
The U2000 Series’ fast measurement speed helps reduce test time. This, coupled with the capability to enable monitoring of more than 20 channels simultaneously, is an advantage in the production line where efficiency is of utmost priority.
The U2000 Series has both internal and external zeroing capabilities. With internal zeroing, high isolation switches in the sensor are opened to isolate the sensor from the device-under-test (DUT) it is connected to. As such, you don’t need to power-off the DUT or disconnect the sensors. This speeds up testing and reduces sensor wear-and-tear.
No manual input of calibration data is required. All calibration factors, as well as temperature and linearity corrections, are stored in the sensors’ EEPROM, auto-downloaded at calibration.
Often times, you’d need to automate your tests. The U2000 Series sensors are well-equipped for seamless integration to your system with industry-standard SCPI compatibility. They also come with built-in triggering capability to allow receipt of external triggers from other instruments.
Transform your signal generators and spectrum analyzers into accurate power meters:
You could literally have a power meter next to you—or instead, turn your Keysight MXG signal generator or N9340A/B handheld spectrum analyzer into a power meter for accurate power measurements. Even with the U2000 connected, you can switch between power measurements and the device’s original function at any time. You can also use the U2000 with your Keysight PNA network analyzer for source power calibration.
Intuitive power analysis software:
The U2000 Series is supported by the Keysight BenchVue software and BV0007B Power Meter/Sensor Control and Analysis app. Once you plug the USB power sensor into a PC and run the software you can see measurement results in a wide array of display formats and log data without any programming.
Key features:
–Compact, lightweight solutions
–Quick, simple set-up
–High accuracy, high power
–Internal zeroing capability
–Fast reading speed
–Wide frequency range: 9 kHz to 24 GHz (sensor option dependant)
–Wide dynamic range: –60 to +44 dBm
–Support internal and external trigger measurements
–Trace display capability enables easy trigger level and gate setup for burst signals
–Allows remote measurements beyond cable length
–Enables monitoring of more than 20 channels simultaneously
–Converts select Keysight instruments to power meters
–Feature-packed software provides various capabilities for easy testing and analysis
–Average power measurements of CW and modulated signals, including GSM, EDGE, WLAN and WiMAXTM
|
U2000 、 BV0007B 、 U2000A 、 U2001A 、 U2002A 、 U2004A 、 U2000B 、 U2001B 、 U2000H 、 U2001H 、 U2002H 、 U2001A-H03 、 U2001A-H16 、 U2001A-H25 、 U2002A-H26 、 U2031A 、 U2031B 、 U2031C 、 U2032A 、 U2000A-201 、 U2000A-202 、 U2000B-201 、 U2000A-204 、 U2000A-203 、 E5813A 、 N9340A 、 N9340B |
|
|
[ installation and maintenance of base stations ][ production testing of wireless components ][ R&D of wireless components ] |
|
|
Datasheet |
|
|
|
|
Please see the document for details |
|
|
|
|
|
|
|
|
|
|
|
English Chinese Chinese and English Japanese |
|
|
July 24, 2018 |
|
|
|
|
|
5989-6278EN |
|
|
4.5 MB |
- +1 Like
- Add to Favorites
Recommend
- Keysight Technologies Acquires Quantum Benchmar, Augmenting Keysight‘s Quantum Portfolio
- Keysight First to Gain OmniAir Qualified Test Equipment Status, Accelerating C-V2X Device Certification
- Keysight First to Gain GCF Approval of Cases for Validating 5G New Radio mmWave Devices in Standalone Mode
- Keysight Massively Parallel Board Test System Selected by LACROIX in Automotive Printed Circuit Board Manufacturing
- Keysight, TIM and JMA Wireless Join Forces to Showcase O-RAN Technology at Mobile World Congress 2021
- Keysight, Xilinx and Cisco Showcase Solutions that Support Smooth Migration from 4G LTE Networks to 5G Open RAN
- Keysight Unveils the First Media Access Control Security Test Solution for High Speed Ethernet
- Keysight, MediaTek Join Forces to Establish 5G Connectivity Based on 3GPP Release 16 Specifications
All reproduced articles on this site are for the purpose of conveying more information and clearly indicate the source. If media or individuals who do not want to be reproduced can contact us, which will be deleted.
Integrated Circuits
Discrete Components
Connectors & Structural Components
Assembly UnitModules & Accessories
Power Supplies & Power Modules
Electronic Materials
Instrumentation & Test Kit
Electrical Tools & Materials
Mechatronics
Processing & Customization
