TVS Diodes Datasheet
© 2023 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: GD. 12/05/23
1
5.0SMDJxxS Series
Single Chip Design
Agency Agency File Number
E230531
The 5.0SMDJxxS series, single chip design is designed specifically
to protect sensitive electronic equipment from voltage transients
induced by lightning and other transient voltage events.
TVS components are ideal for the protection of I/O Interfaces, VCC
bus and other vulnerable circuits used in Telecom, Computer,
Industrial and Consumer electronic applications.
Applications
Features
Maximum Ratings and Thermal Characteristics (T
A
=25
O
C
unless otherwise noted)
Agency Approvals
■ 5000W peak pulse power
capability at 10/1000μs
waveform, repetition rate (duty
cycles):0.01%
■ Recognized to UL 497B as an
Isolated Loop Circuit Protector
■ DO214AB SMT package for
minimized board space
■ Low profile package
■ Typical failure mode is short
from over-specified voltage or
current
■ Whisker test is conducted
based on JEDEC JESD201A
per its table 4a and 4c
■ ESD protection of data lines in
accordance with IEC 61000-
4-2, ESD 30kV (Air), 30kV
(Contact)
■ EFT protection of data lines in
accordance with IEC 61000-
4-4
■ Built-in strain relief
■ Glass passivated chip junction
■ Very fast response time
■ Excellent clamping capability
■ Low incremental surge
resistance
■ Typical IR less than 2μA when
VBR min>12V
■ High temperature to reflow
soldering guaranteed:
260°C/10sec
■ VBR @ TJ= VBR@25°C x (1+αT
x (TJ - 25))(αT:Temperature
Coefficient)
■ UL Recognized compound
meeting flammability rating V-0
■ Meet MSL level1, per
J-STD-020, LF maximun peak
of 260°C
■ Matte tin lead–free plated
■ Halogen free and RoHS
compliant
■ Pb-free E3 means 2nd level
interconnect is Pb-free and
the terminal finish material is
tin(Sn) (IPC/JEDEC J-STD-
609A.01)
Parameter Symbol Value Unit
Maximum Peak Pulse Power Dissipation
at T
L
=25
O
C by 10/1000µs Waveform
(Fig.2)(Note 1)(Note 2)
P
PPM
5000 W
Power Dissipation on Infinite Heat Sink
at T
L
=50
O
C (Note 4)
P
D
6.5 W
Peak Forward Surge Current, 8.3ms
Single Half Sine Wave (Note 3)
I
FSM
300 A
Maximum Instantaneous Forward
Voltage at 100A for Unidirectional Only
V
F
3.5 V
Operating Temperature Range T
J
-65 to 150 °C
Storage Temperature Range T
STG
-65 to 175 °C
Typical Thermal Resistance Junction to
Lead
R
θJL
15 °C/W
Typical Thermal Resistance Junction to
Ambient
R
θJA
75 °C/W
Description
Functional Diagram
Bi-directional
Uni-directional
Cathode
Anode
Notes:
1. Non-repetitive current pulse , per Fig. 4 and derated above T
J
(initial) =25
O
C per Fig. 3.
2. Voltage of 6.0V~60V products’s peak pulse power dissipation is 5000W, and 64V and 70V is 4500W. Bi-
directional products 33V~58V are also 4500W.
3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional components only,duty
cycle=4 per minute maximum.
4. Mounted on copper pad area of 0.31x0.31” (8.0 x 8.0mm) to each terminal.
Resources Accessories Samples
Additional Information