Accessories
www.vishay.com
Vishay BCcomponents
Revision: 01-Dec-17
1
Document Number: 28348
For technical questions, contact: aluminumcaps2@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Aluminum Electrolytic Capacitors - Accessories
(Vishay BCcomponents)
RESISTORS FOR TERMINAL MOUNTING
Resistors are used to balance the voltage over a series connection of screw terminal capacitors or to ensure discharge to a safe
voltage after power down. Vishay provides the CMS series of resistors
, which are suited for direct mounting on the terminals of
screw terminal capacitors.
MOUNTING ACCESSORIES
CLAMPS FOR ST TYPES
To facilitate vertical mounting, a series of rigid clamps is available. These are made of zinc plated steel, chromium (III)
passivated, or stainless steel (Ø D = 76 mm).
The clamps have either two or three mounting lugs, may be easily slipped over the capacitor and then clamped with
a nut and bolt. Five types of clamps are available, one for each case diameter.
They are delivered without nuts or bolts.
To avoid damaging the insulation sleeve, do not overtighten the clamp screw.
DIMENSIONS in inches [millimeters]
DIAMETER MODEL
CORE DIMENSIONS in inch [mm] TERMINAL DESIGNATION
A
TYPICAL
B
± 0.031 [0.79]
C
± 0.062 [1.59]
M
± 0.0118 [0.3]
CM
HOLE DIAMETER
TYPICAL
CA
HOLE DIAMETER
TYPICAL
Ø 50 mm CMS16
0.562
[14.27]
0.312
[7.92]
1.250
[31.75]
0.875
[22.23]
0.196
[4.98]
0.265
Ø 65 mm CMS20
0.562
[14.27]
0.312
[7.92]
1.75
[44.45]
1.13
[28.7]
0.196
[4.98]
0.265
[6.73]
Ø 76 mm
CMS22
0.562
[14.27]
0.312
[7.92]
1.75
[44.45]
1.254
[31.85]
0.196
[4.98]
0.265
[6.73]
Ø 90 mm
45° ± 10°
3/4" TYP.
C
B
M
A
Accessories
www.vishay.com
Vishay BCcomponents
Revision: 01-Dec-17
2
Document Number: 28348
For technical questions, contact: aluminumcaps2@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DIMENSIONS in millimeters AND AVAILABLE FORMS
Fig. 1 - Dimensional outline of clamp for case Ø D = 35 mm Fig. 2 - Dimensional outline of clamp for case Ø D = 50 mm
Fig. 3 - Dimensional outline of clamp for case Ø D = 65 mm Fig. 4 - Dimensional outline of clamp for case Ø D = 76 mm
Fig. 5 - Dimensional outline of clamp for case Ø D = 90 mm
0
- 0.5
Ø 4.5 ± 0.1
12
± 0.5
63
35
51.5 ± 0.2
12 ± 0.5
6 ± 1
1
35°
23.5
10
4.5
12.05
11.05
7
6
1
Ø 4.4 min
12.5 max.
4 min.
60°
60°
10.5
50
49
67.5
66.5
80 max.
12.5
11.5
7
6
1
Ø 4.4 min.
65
64
88.5
87.5
101 max.
12.5 max.
4.5
60°
60°
10.5
19
28.5
Ø 5 ± 0.3
1
10.5
10.5
D
15°
12.5
89
99
120°
4.5
7
11
5.5
30 ± 1
Ø 4.2 ± 0.1
24 ± 0.5
4.5
12
120°(3 x)
4.5 ± 0.5
14
7
Ø 90
Ø 101.6 ± 0.5
Ø 111.1 ± 1
1