F
ig 1: Schematics of the a) eGaN switch and b) PIN diode
switch for RF receive coils.
Fig 2: Schematic of test coil with interchangeable detuning
circuits. Pickup loops P1 and P2 are used to quantify detuning.
4879
Enhancement Mode GaN (eGaN® FETs) for Coil Detuning
Michael Twieg
1
, Matthew J Riffe
2
, Michael de Rooij
3
, and Mark A Griswold
1,4
1
Dept. of Electrical Engineering and Computer Science, Case Western Reserve University, Cleveland, OH, United States,
2
Dept. of Biomedical Engineering, Case
Western Reserve University, Cleveland, OH, United States,
3
Efficient Power Conversion Corporation, El Segundo, CA, United States,
4
Dept. of Radiology, Case
Western Reserve University, Cleveland, OH, United States
Target audience: This work is relevant to those interested in RF coil design and patient safety.
Purpose: Coil detuning in RF coils is necessary for patient safety and RF field homogeneity. Decoupling is typically achieved using PIN diodes,
which function as switches to permit or restrict the flow of RF current on coil elements. However, a major drawback to PIN diodes is that they
require large DC bias current in order to achieve a conducting state
1
. DC bias current on a coil presents a potential problem due to the resulting static
B
0
inhomogeneity and power dissipation, which may be especially problematic in dense receive arrays. In this work we demonstrate the use of
Enhancement-Mode Gallium Nitride FETs (eGaN FETs) from Efficient Power Conversion Corporation as a replacement for PIN diodes in active
detuning circuits. The performance of eGaN FETs allows for effective RF switches without the need for large DC bias currents, thus eliminating B
0
inhomogeneity and static dissipation from the switch.
Methods: eGaN FETs: An effective coil detuning network relies on a switching device
whose impedance changes greatly between its on and off states. For example, a
MA4P7470F-1072T PIN diode from MACOM Technologies has a resistance near 0.5
while forward biased with 100 mA, while when reverse biased with 10 V its impedance
increases to near 20 k with less than 1 pF of parallel capacitance. It has been previously
suggested
2
that field effect transistors (FETs) be used as an alternative to PIN diodes for
coil detuning, but the performance of FETs suffers since achieving a comparably low on-
state resistance also requires a large parasitic output capacitance C
OSS
, which causes a
lowered off-state impedance. However, recent advances in eGaN FETs have yielded
devices with on-state resistances less than 0.125 with C
OSS
of just 40 pF
3
, making them
potentially competitive. eGaN FET RF switch: The schematic of the fundamental eGaN
FET switch is shown in fig 1a. A pair of common source devices is used so that the
switch can operate in all four quadrants. When biased in the off state, the switch still has
significant parallel capacitance due to C
OSS
. The off-state impedance of the switch is
increased by adding a resonant inductor L
1
in parallel. When in the off state, coil current
is allowed to flow normally through coil capacitor C
C
. When biased in the on state,
inductor L
2
is shunted in parallel with C
C
, forming a high impedance at f
0
and blocking
coil current. This is analogous to the operation of the typical PIN diode detuning circuit
shown in fig 1b. The gate biasing network consists of two inductors selected for self-
resonance at f
0
, as well as a TVS diode D
1
and a pull down resistor to protect the gates.
The control signal would ideally be a 0-5 V logic signal with only milliamps of current capacity.
Performance characterization: The performance of the eGaN FET method (fig 1a) was compared
with a typical PIN diode method (fig 1b). A 10 cm square surface coil was constructed and tuned for
63.6MHz. A C
C
value of 53 pF was used in both detuning circuits. The coil was designed to allow
for different detuning networks to be interchanged easily while minimizing effects on the coil itself
(see fig 2). PIN diode networks were made using the MA4P7470F-1072T, while eGaN circuits were
made using the EPC8004 from EPC. A benchtop experiment using decoupled RF pickup loops in
fixed locations was performed to measure the performance of the detuning circuits in the detuned
state. The S
21
between the two pickup loops was measured, and the difference in S
21
at f
0
between
the tuned and detuned states was observed. Imaging experiments were performed with each
detuning circuit to quantify their effect on signal dynamic range (DR) and image SNR
4
. A GRE
sequence (TE=10 ms, TR=100 ms, FA=20°, 256x256, N
AVG
=1) was performed using a Siemens
Espree 1.5 T scanner. All experiments were performed with the coil placed 15 mm above a flat 5.3
L saline phantom (2.4 g/L NaCl, 1.0 g/L CuSO
4
), with the coil impedance matched to 50 (S
11
<-45
dB). When using the eGaN FET switch, an external circuit was used to convert the normal bias
signal from the scanner into a 0-5V logic signal.
Results: Table 1 summarizes the results of the imaging and benchtop experiments described above.
The detuning measurement showed a -6.8 dB improvement from the eGaN FET switch vs. the PIN diode switch. The imaging experiments showed a
0.07 dB drop in signal DR and a 0.12 dB drop in image SNR with the eGaN FET switch. The measured current draw of the eGaN switch was 75 A.
Fig 3 shows photos of the two switch networks used in the measurements.
Discussion and conclusion: These results suggest that eGaN FETs have several advantages over PIN diode switches for detuning networks in
receive coils. The eGaN FET switch had a lower on state resistance than typical PIN diodes, giving higher detuning performance and power
handling. We observed a 0.12 dB decrease in image SNR, though this loss may be further mitigated by increasing the value of C
C
. The eGaN FET
switch required <100 A of control current, and the eGaN devices have been previously shown to have negligible susceptibility
5
, thus eliminating B
0
inhomogeneity concerns from coil detuning. Given the high current capability of eGaN FETs, it is expected that they would also be suitable for use in
transmit coil detuning, and possibly transmit/receive switches. This work also suggests that current eGaN FETs would be effective for operation at
128 MHz (
1
H at 3T), and that passive and active detuning functionality may also be realizable within the same switch element, further improving
overall system safety. The relative cost of eGaN FETs is expected to be comparable, once the next-generation eGaN FETs reach mass production.
Acknowledgements: This work was supported by Siemens healthcare and Efficient Power Conversion Corporation.
References:
1
Haase H et al, CMR, vol. 12-6, pp. 361-388, 2000.
2
Reykowski A, Patent WO2012160518 A1, 2012.
3
EPC Corporation, 2013
[Online].
4
Riffe M et al, MRM 2013, doi: 10.1002/mrm.24613.
5
Twieg M et al, ISMRM 2013.
Detuning (dB)
DR (dB)
SNR (dB)
PIN diode -47.0 48.48 27.81
eGaN FETs -53.8 48.35 27.69
Change -6.8 -0.07 -0.12
Table 1: Results summary for coil performance
Figure 3: Photograph of the eGaN detuning circuit
(top) and PIN diode detuning circuit (bottom).
a)
b)
Joint Annual Meeting ISMRM-ESMRMB 2014 ○ 10-16 May 2014 ○ Milan, Italy