Page | 1
Enabling Wireless Sensing + BLE Applications
Part Number: NW-MOT-ICM42688P Web: https://www.notwired.co Toll-Free: 1-800-777-7334 Rev. 1/9/2020
Description:
The TDK InvenSense ICM-42688-P is a 6-axis MotionTracking device that combines a 3-axis gyroscope, and a 3-
axis accelerometer in a small 2.5x3x0.91 mm (14-pin LGA) package. The ICM-42688-P features include on-chip
16-bit ADCs, programmable digital filters, an embedded temperature sensor, and programmable interrupts.
The device features I3C
SM
, I
2
C and SPI serial interfaces, a VDD operating range of 1.71 V to 3.6 V, and a
separate VDDIO operating range of 1.71 V to 3.6 V.
The ICM-42688-P also features a 2K-byte FIFO that can lower the traffic on the serial bus interface and reduce
power consumption by allowing the system processor to burst read sensor data and then go into a low-power
mode. ICM-42688-P, with its 6-axis integration, enables manufacturers to eliminate the costly and complex
selection, qualification, and system level integration of discrete devices, guaranteeing optimal motion
performance for consumers.
The NM-MOT-ICM42688P provides an easy to use, low-cost, very small breakout board for the ICM-42688-P.
All pins are all mapped to standard 2.54mm/0.1” headers. This allows for use in a standard bread board or to
be ‘wired’ into an application. The header-header spacing is 7.62mm (300mil).
Additional Information:
For more information on the NW-MOT-42688P users can get the complete datasheet from the link below.
https://www.invensense.com/products/motion-tracking/6-axis/
Features:
• Ultra-small 16.3x13.8mm (0.59”x0.5”) breakout board with .1”/2.54mm header spacing that can be
directly soldered into a prototype or used with a breadboard.
• 7.62mm (300mil) header-header spacing.
• All ICM-42688-P pins are mapped to header pins
Motion
NW-MOT-ICM42688P Coming Soon
Break out Board for the InvenSense ICM-42688-P MEMS MotionTracking
TM
1
1
2
2
3
3
4
4
D D
C C
B B
A A
Component Di str ibu tor s, Inc
CDI Engineering Lab
1301 W PG BH, STE110
Richardson, TX 75 081
1
NW-MOT-ICM42688-P
1 V2
5/31/2019
NW-MOT-ICM42688-P.SchDo c
Title
Size: Number:
Date Modified:
File:
Revision:
Sheet of
A4
CDI Confidential
Proprietary
VDDIO
0402
0mR
62.5mW
5%
R2
GND
0402
0mR
62.5mW
5%
R1
GND
GND
0402
16V
X7R
100nF
C1
0402
2.2uF
X5R
6.3V
C2
0402
10nF
X7R
16V
C3
GND
VDD
VDDIO
SCL
SDA
CS
GND
GND
GND
2
1
3
4
5
P1
61300511121
2
1
3
4
5
P2
61300511121
INT
FSYNC
SCL
SDA
0402
1%
10kR
63mW
R4
0402
1%
10kR
63mW
R5
0402
0mR
62.5mW
5%
R3
VDDIO
GND
VDD
VDDIO
FSYNC
INT
GND
ADO/SDO
ADO/SDO
AP_SCL
13
AP_SDA
14
AP_AD0
1
GND
6
VDD
8
RESV-NC
2
VDDIO
5
RESV-NC
10
RESV-NC
3
RESV-NC
11
AP_CS
12
INT1/INT
4
INT2/FSYN C
9
RESV-NC
7
U1
ICM4268 8-P
0402
0mR
62.5mW
5%
R6
0402
0mR
62.5mW
5%
R7
CS
VDDIO
Note: If user is trying to test CLK IN/ FSYNC function ali t y, leave R3 unpopulated.
If R1 is populated,
AP_AD0 = 0 and ,
I2C address is 1101000
If R2 is populated,
AP_AD0 = 1 and ,
I2C address is 1101001
Note: From R1 & R2, choo s e on e to
popul ate, depend i n g on if user want s
AP_AD0 add ress low or high .
PIC101
PIC102
COC1
PIC201
PIC202
COC2
PIC301
PIC302
COC3
PIP101
PIP102
PIP103
PIP104
PIP105
COP1
PIP201
PIP202
PIP203
PIP204
PIP205
COP2
PIR101
PIR102
COR1
PIR201
PIR202
COR2
PIR301
PIR302
COR3
PIR401
PIR402
COR4
PIR501
PIR502
COR5
PIR601
PIR602
COR6
PIR701
PIR702
COR7
PIU101
PIU102
PIU103
PIU104
PIU105
PIU106
PIU107
PIU108
PIU109
PIU1010
PIU1011
PIU1012
PIU1013
PIU1014
COU1
PIP203
PIR102
PIR202
PIU101
PIP204
PIR702
PIP104
PIR301
PIU109
PIC101
PIC202
PIC301
PIP102
PIR101
PIR302
PIU106
PIU107
PIU1011
PIP105
PIU104
PIU1010
PIU103
PIU102
PIR602
PIR701
PIU1012
PIP205
PIP202
PIR502
PIU1013
PIP201
PIR402
PIU1014
PIC102
PIC201
PIP101
PIU108
PIC302
PIP103
PIR201
PIR401
PIR501
PIR601
PIU105