FT48T-B7105 Quick Installation Guide
Document # D2414-100/ Revision 1.0
3
Motherboard Placement
A
B
1
b
Battery
CPU1
CPU0
BIOS_SPI_
SOCKET
C
D
E
F
G
P1_MC1_DIM_CH_F0P1_MC1_DIM_CH_F0
a
i
ii
H
I
J
K
P1_MC1_DIM_CH_E0P1_MC1_DIM_CH_E0
P1_MC1_DIM_CH_D0
P1_MC1_DIM_CH_D0
P0_MC0_DIM_CH_C0
P0_MC0_DIM_CH_C0
P0_MC0_DIM_CH_B0
P0_MC0_DIM_CH_B0
P0_MC0_DIM_CH_A0
P0_MC0_DIM_CH_A0
P0_MC1_DIM_CH_D0
P0_MC1_DIM_CH_D0
P0_MC1_DIM_CH_E0
P0_MC1_DIM_CH_E0
P0_MC1_DIM_CH_F0
P0_MC1_DIM_CH_F0
P1_MC0_DIM_CH_A0
P1_MC0_DIM_CH_A0
P1_MC0_DIM_CH_B0
P1_MC0_DIM_CH_B0
P1_MC0_DIM_CH_C0
P1_MC0_DIM_CH_C0
2
3
4
5
6
7 8 9 10 11 12 13 14 15 16 17 18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
3435
Read Me First
1. The Barebone User’s Manual is available for download from our Web site at http://www.tyan.com. Make sure to read all
precautions and instructions before you start installing the server system.
2. Refer all servicing to qualified personnel to avoid the risk of damage to the server system.
3. Exercise normal ESD (Electrostatic Discharge) procedures during system integration. TYAN/MiTAC recommends wearing
gloves and an anti-static wrist strap to avoid possible damage to the equipment.
4. Current processor socket design places the pins on the motherboard instead of the processor itself. Exercise caution when
installing the processors as the manufacturer’s warranty does not cover damage inflicted upon the motherboard, including
damage to the CPU sockets.
Tools Required
1
General Information
2
System Installation
Box Content
Accessories
NOTE: Please save and replace the CPU
protection cap when returning
the server board for service.
5
Caution
Motherboard Placement
CPU Cover for DOA/RMA
Locate the External I/O Port
Install the Memory
Minimum Hardware Requirements
To avoid integration difficulties and possible board damage, your system must meet the following minimum requirements:
• Processor: Support (2) Intel® Xeon® Scalable processors
• Memory Type: (6+6) DIMM slots of DDR4 2666 MHz R-DIMM memory
• Hard Disk Drives: 2.5" or 3.5" SATA/SAS HDD
• Rack Mount Kit : Standard 19" equipment rack
NOTE: The updated hardware requirements of the system please refer to the barebones user’s manual on our website at
http://www.tyan.com
Required Hardware Components
Remove the Air Duct
Preparing the Chassis
Read normal ESD (Electrostatic Discharge) procedures.
Place your TYAN
®
Server Chassis on a flat anti-static surface to perform the following integration procedures. Read
ESD procedures before reaching inside to install components.
Open the Chassis
Installing the Add-On card (Optional)
1
Unlock the clips.
2
Insert the memory module.
3
Lock the clips.
4
I/O Ports
1
Loosen the 2 thumb screws and remove the
screw on the rear of the chassis.
2
Slide the top cover and remove.
1
Remove the 2 screws on the sides of
the air duct. Then slide the air duct
and remove from the chassis.
Phillips Screwdriver
Anti-Static Wrist Strap
T30 Security Torx Screwdriver
CONNECTORS
1
AUDIO PHONE JACK_13P_VERTICAL_D3 (J2)
2
Dedicated IPMI port + USB3.0x2
(USB3_IPMI_LAN1)
3
LAN ( RJ-45) (J184)
4
LAN ( RJ-45) (J183)
5
VGACON-RA (VGA1)
6
CPU FAN Connectors (CPU1_FAN_1)
7
M.2 2280/22110 slot (PCI-e x2 from PCH)
(NGFF1)
8
FP-VGA-HD (VGA2)
9
IPMB Pin Header (IPMB_HD1)
10
COM-Port HRD (HD_COM2)
11
5P*2_USB2.0x2 HD (J43)
12
M.2 2280/22110 slot (PCI-e x2 from PCH) (NGFF2)
13
SATA RAID KEY (J122)
14 TYPE-A USB2.0 Connector (TYPEA_USB2)
15
Front USB3.0 Connector (USB3_FPIO2)
16
System Power Button (PWR_BTN1)
17
USB3.0-TYPE-RA (TYPEA_USB3)
18
Front Panel Connector (SSI_FP)
19
System FAN Connectors (SYS_FAN_4)
20
SSGPIO Header (SSATA_SGPIO1)
21
sSATA：sSerial Advanced Technology
Attachment Gen3 (SSATA0)
22
sSATA：sSerial Advanced Technology
Attachment Gen3 (SSATA1)
23
SATA：Serial Advanced Technology
Attachment Gen3 (SATA0_3)
SLOTS
A
PCI Express Gen 3 x 8 (PCIE_1)
B
PCI Express Gen 3 x 16 (PCIE_2)
C
PCI Express Gen 3 x 8 (PCIE_3)
D
PCI Express Gen 3 x16 (PCIE_4)
E
PCI Express Gen 3 x 8 (PCIE_5)
F
PCI Express Gen 3 x 16 (PCIE_6)
G
PCI Express Gen 3 x 8 (PCIE_7)
H
PCI Express Gen 3 x 16 (PCIE_8)
I
PCI Express Gen 3 x 8 (PCIE_9)
J
PCI Express Gen 3 x16 (PCIE_10)
K
PCI Express Gen 3 x16 (PCIE_11)
24
System Reset Button (RST_BTN1)
25
SATA：Serial Advanced Technology
Attachment Gen3 (SATA4_7)
26
FLASH SECURITY OVERRIDE (J119)
27
System FAN Connectors (SYS_FAN_3)
28
System FAN Connectors (SYS_FAN_2)
29
PSMI Connector (5P_PSMI)
30
FM_PCH_BIOS_RCVR_SPKR (J194)
31
12Px2_ATX_PWR (PWCN1)
32 CPU FAN Connectors (CPU0_FAN_1)
33
4Px2_ATX_PWR (PWCN3)
34
System FAN Connectors (SYS_FAN_1)
35 4Px2_ATX_PWR (PWCN2)
LEDs
i
BMC Heartbeat-LED (BMC_HB_LED)
ii
ID_LED BLUE_3010 (ID_LED)
JUMPERS
a
INTRUDER JUMPER (J202)
b
CMOS CLEAR JUMPER (J104)
Install the Processor
1
Align and install the processor
on the carrier.
2
Carefully flip the heatsink. Then
install the carrier assembly on the
bottom of the heatsink and make
sure the gold arrow is located in the
correct direction.
3
Remove the CPU cover.
NOTE: Save and replace
the CPU cover if the
processor is removed
from its socket.
4
Align the heatsink with the CPU
socket by the guide pins and make
sure the gold arrow is located in
the correct direction. Then place
the heatsink onto the top of the
CPU socket.
5
To secure the heatsink, use a T30 Security
Torx to tighten the screws in a sequential
order (1234).
NOTE: When disassembling the heatsink,
loosen the screws in reverse order
(4321).
NOTE: A new heatsink comes with
pre-applied thermal grease.
Once the heatsink has been removed from
the processor, you need to clean the
processor and heatsink using an alcohol
solvent. Then apply new thermal grease
before reinstalling the heatsink.
(1) Sliding Rail
(Optional)
(1) CD_ROM_Rail
Screw Kit
(5) GPU Card
Holder Kit
(1) Air Duct Kit
(for B7105F48TV4HR-2T-N only)
(5) 8-Pin CPU
Power Cable(2) CPU heatsink
(2) US AC
Power Cord
(2) EU AC
Power Cord
(1) HDD
Screw Pack
(2) M.2
Screw Pack
(3) System Fans
(6 system fans for
B7105F48TV4HR-2T-N)
(1) M1019-FPB
Front Panel Board
(pre-installed)
(1) M1622F48T-D-PDB
Power Distribution
Board (pre-installed)
4U barebone,
(4) hot swap HDD bays
(1) TYAN
®
S7105AGM2NR-2T
System Board (pre-installed)
1
Align and slide the air duct in place. Then use the 2
screws to secure the air duct to the chassis.
2
Remove the screws securing the 2 PCI brackets and
remove the brackets from their slots.
5
Connect the GPU power cable.
3
Align and install the GPU bracket to the GPU card.
Then use the 3 screws to secure the bracket to the
GPU card.
4
Install the GPU card assembly into the PCIE Gen. 3 slot,
and then secure it with 2 screws.
6
Route the GPU power cable through the side opening
on the air duct. Then slide the air duct in place and
secure it with 3 screws.
(1) M1809F77A-FB
Fan Board (pre-installed)
(1+1), 2000W
Power Supply Unit
(3) CD_ROM_Rail
(1) Quick Installation
Guide
(2) CPU Clip
Quick Installation
Guide
(2) SATA Internal
Cable
(2) SATA Power
Cable
(5) 6-Pin +8-pin
PCIe Power Cable
(4) Foot Stand &
Screws
4
1
3
2
(1) M1237F48-BP6-4-7055,
R01 Backplane Board
(1) Addendum
for China Use Only
Addendum
for China Use Only
(1) Driver’s
and Utility CD
RJ45 LAN Port
#2 (LAN2)
Dedicated IPMI Port
USB3.0 (x2)Microphone
Line Out
Line In
VGA Port
RJ45 LAN Port #1
(LAN1)
Install the Hard Disks (3.5” or 2.5”)
1
Press the locking lever latch and lift the locking lever
upwards to its OPEN position.
3a
Install a 3.5” hard disk drive into the HDD tray, and
then secure it with 4 screws.
4
Install the HDD tray into its bay and press firmly until
it is fully seated.
2
Pull the locking lever to remove the HDD tray from its
bay.
3b
Install a 2.5” hard disk drive into the HDD tray, and
then secure it with 4 screws.
5
Close the locking lever and press the latch firmly to
secure the tray in place.
Repeat the same procedures to install other HDD trays.