UBX-13003492 Confidential & Proprietary Page 1 of 3
locate, communicate, accelerate
Information Note
Product Name
Ordering Code
Design Status
Created
Document #
LISA-U200
LISA-U260
LISA-U270
LISA-U200-02S
LISA-U200-62S
LISA-U260-02S
LISA-U270-02S
LISA-U270-62S
Initial
Production
este
22.08.2013
UBX-13003492
1.
Identification
Package
1
No of units
1
Marking
Data Code
Firmware
22.90
2.
Restriction as compared to specification
See Annex A.
3.
Detected Defects
See Annex B.
4.
Workarounds
Workarounds – if available – are described in Annex A and B.
5.
Test Status
Tested according to specification
Untested
Limited testing. see Annex A & B
6.
References
[1] LISA-U2xx Data-sheet, u-blox Document UBX-13001734, Revision B
[2] u-blox AT-commands Manual, u-blox Document WLS-SW-11000, Revision C3
[3] LISA-U System Integration Manual, u-blox document UBX-13001118, Revision B
7.
Expected Customer Feedback
Expected by
Feedback should be provided to u-blox technical support.
8.
Delivery Release
Product Manager
Quality Manager
Name: Ezra Stein
Date: 22.08.2013
Name:
Date:
UBX-13003492 Confidential & Proprietary Page 2 of 3
locate, communicate, accelerate
Annex A – Restrictions compared to specifications
Hardware
No restrictions.
Features / Firmware / Software
Audio over USB interface is not implemented. Feature will be implemented in a next Firmware version.
Control Plane Aiding for A-GPS is not implemented. Feature will be implemented in a next Firmware
version.
TX data ready feature (see [2]) doesn’t work with ublox7 GNSS modules. The feature works with ublox6
GNSS modules.
Annex B – Known bugs and limitation
The maximum file size on FFS is limited to 5 Mbytes.
Annex C – New features implemented in this firmware version
Features implemented in all modules
Add the features SUSPEND and RESUME to FTP functionality. See [2] chapter FTP.
Allow software Flow Control (XON/OFF) with external TCP/IP.
Improve the performance of Jamming Detection algorithm. AT command: +USD
Configure RING line to indicate in-coming data. AT command: +URING
Number of PDP context is increase to maximum 11 (was before 3). AT command: +CGDCONT
Allow the AT command +CSQ also when the no SIM card is present.
Allow to append data into a file in the local File System. AT command: +URDBLOCK
Allow setting the local port for a TCP socket. AT command: +USOCR
Fast Dormancy. The feature is per default disabled and must be enabled. AT command:+UFDAC
Power Saving mode can be controlled by DTR line. AT command:+UPSV=3
Automatic Time Zone Update save in NVRAM. AT command: +CTZU
Configuration of the timer for “Direct Link” mode. AT command: +UDCONF=5
“always-on”: module establishes automatically a TCP direct link connection at switch on and will keep it
alive. AT command: +USOAO
Lock the module to the current base-station and do not do handover. AT command: +UCELLLOCK
Improvements in the functionality of CellLocate: automatically sending a UBX command when
CellLocate was used.
Decoding of DTMF. AT command: +UDTMFD .
Full support of eCall, ERA/GLONASS and InBand modem. See [2] chapter eCall and In-Band Modem.
Notification of change of IP-address: automatically inform a server when its IP address has changed.
AT command: +UIPCHGN .
Use a commercial Dynamic DNS server in order to allow automatic DNS propagation when DNS is used
and IP change. AT command: +UDYNDNS .
UART support for 7 bit / E / 1 format. AT command: +ICF .