6/23/16
GaAs DOUBLE-BALANCED MIXER MM1-0320H
Features
Compact Chip Style Package (0.058” x 0.046”x0.004”)
CAD Optimized for Superior Isolation and Spurious Response
Broadband Performance
Excellent Unit-to-Unit Repeatability
Fully nonlinear software models available with Marki PDK for Microwave Office®
RoHS Compliant
Electrical Specifications - Specifications guaranteed from -55 to +100C, measured in a 50Ω system.
Specifications are shown for Configurations A (B). See page 2 for port locations.
All bare die are 100% DC tested and 100% visual inspected. RF testing is performed
on a sample basis to verify conformance to datasheet guaranteed specifications.
Consult factory for more information.
Parameter
LO
RF
IF
Min
Typ
Max
LO drive level (dBm)
(GHz)
(GHz)
(GHz)
Conversion Loss
3.5-20
DC-4
8 (9)
13 (16)
Isolation (dB)
LO-RF
See
LO-IF
Plots
RF-IF
Input 1 dB Compression (dBm)
+9
Config. A: +13 to +20
+9
Config. B: +12 to +17
Input Two-Tone Third Order
Intercept Point (dBm)
+20
Config. A: +13 to +20
+20
Config. B: +12 to +17
Part Number Options
Please specify diode level and package style by adding to model number.
Package Styles
Examples
Connectorized
1, 3
S
MM1-0320HCH-2, MM1-0320HS
Chip
2, 3
(RoHS)
CH-2
MM1-0320
(Model)
H
(Diode Option)
CH-2
(Package)
1
Connectorized package consists of chip package wire bonded to a substrate, equivalent to an evaluation board.
2
Chip package connects to external circuit through wire bondable gold pads.
3
Note: For port locations and I/O designations, refer to the drawings on page 2 of this document.
215 Vineyard Court, Morgan Hill, CA 95037 | Ph: 408.778.4200 | Fax 408.778.4300 | info@markimicrowave.com
The MM1-0320H is a passive double balanced MMIC mixer. It
features excellent conversion loss, superior isolations and
spurious performance across a broad bandwidth, in a highly
miniaturized form factor. Accurate, nonlinear simulation
models are available for Microwave Office® through the Marki
Microwave PDK. The MM1-0320H is available as a wire
bondable chip or an SMA connectorized package. The MM1-
0320H is a superior alternative to Marki Microwave carrier and
packaged M1 and M3 mixers.
6/23/16
GaAs DOUBLE-BALANCED MIXER
MM1-0320H
Page 2
LO/RF 3.5 to 20 GHz
IF DC to 4 GHz
1. Configuration A/B refer to the same part number (MM1-0320H) used in one of two different ways for optimal spurious performance. For the
lowest conversion loss, use the mixer in Configuration A (port 1 as the LO input, port 2 as the RF input or output). If you need to use a lower
LO drive, use the mixer in Configuration B (port 1 as the RF input or output, port 2 as the LO input). For optimal spurious suppression,
experimentation or simulation is required to choose between Configuration A and B. For more information, see here.
2
3
1
.058
[1.47]
.029
[.74]
.003 Typ
[.09]
.046
[1.17]
.004
[.10]
.006 x .003
Bonding Pad,
3 PL
[.152]
[.076]
.023
[.58]
.005
[.13]
min clearance
INCH
[MM]
PROJECTION
1. CH Substrate material is .004 thick GaAs.
2. I/O traces and ground plane finish are 2 microns Au.
3. See mounting and bonding recommendations at the end of this document for further information.
MM10320H
Ø.067 Thru, 4 PL
[5.0]
.20
[1.70]
[7.11]
.280
[6.60]
.260
[13.21]
.520
[11.07]
.436
[1.07]
.042
[4.06]
.160
.560
[6.10]
[14.22]
.240
.06 Rad
4 PL
[1.5]
[5.0]
.20
[9.9]
.39
PROJECTION
[MM]
INCH
D/C
Configuration A
LO 1
2
3
Function
RF
IF
Port Number
Configuration B
3
2
1
Port Number
Note: S-Package Connectors are not removeable
2
1 3
Connector
SMA Female
SMA Female
SMA Female
Type