Mounting Kits For Wide Panel Antennas

•

DB380 and DB380-3 Pipe Mounts

DB5083 and DB5083D Downtilt Mounts

Page 1 of 4

Installation Instructions

Bulletin 095351-000 • Revision AE • July 2013

CommScope Infrastructure Academy offers installation training.

PARTS LIST

3 M10-1.5 X 35 Hex HD Bolt, HTSTL,GALV 4 6

58 N.m (43ft Ibs)M12

37 N.m (27ft Ibs)M10

MAXIMUM TORQUE VALUES

4 M10 Split Lock Washer, STL,GALV 4 6

5 M10-1.5 Hex HD Nut, STL,GALV

6 M12-1.75 X 190 Hex HD Bolt, STL,GALV 46

7 M12 Flat Washer, STL,GALV 8 12

8 M12 Split Lock Washer, STL,GALV 4 6

M12-1.75 Hex HD Nut, STL,GALV

812

Item Description

Qty

DB380 DB380-3

1 Bracket With Tabs 2 3

2 Bracket Without Tabs 2

Item Description

Qty

DB5083 DB5083D

1 Downtilt Bracket 1 2

2 Downtilt Bracket 1 2

3 M10 Split Lock Washer, STL,GALV 4 8

4 M10-1.5 Hex HD Nut, STL,GALV 8 16

5 M10-1.5 X 35 Hex HD Bolt, HTSTL, GALV 4 8

6 M10 Tooth Lock Washer, STL,GALV 2 4

DB380/DB380-3

GENERAL INFORMATION

with no significant side wind load.

• Position the antenna with its “up” arrow label

pointing upward before installation. This orientation

allows the drain holes to be on the bottom of the

(continued on page 2)

antenna.

mount).

has 2 mounting brackets (uses DB5083 for downtilt

• DB380 has 2 clamp assemblies. Each clamp assembly

angle members up to 2.5” (63.5 mm) on a side.

PRE-INSTALLATION INSTRUCTIONS

60 to 115 mm) OD or• Fits round members 2.4” to 4.5” (

mount).

has 3 mounting brackets (uses DB5083D for downtilt

• DB380-3 has 3 clamp assemblies. Each clamp assembly

• Examine antenna and hardware to ensure that all

parts are enclosed and that there is no physical

damage.

• Check to ensure that the antenna feed connector

mates with the jumper cable.

• Verify that the frequency range shown on the label

on the back of the antenna matches the frequency

range of the station equipment.

Note: Minimum pipe diameter recommended is 60 mm (2.4”). These

mounts can be used on pipe diameters measuring down to 33 mm (1.3”);

this is only recommended for building mounts or however, applications

DB5083/DB5083D

results of improper or unsafe installation practices.

󳣝

is in the area.Do not use metal

day or when lightning or thunder

Do not install on a wet or windy

rubber gloves.

including a long-sleeved shirt and

heels. Wear protective clothing

Wear shoes with rubber soles and Do not install near power lines.

electrocute you.

Assume any wire or line can

and guy wires look the same.

Power lines, telephone lines,

ladder.

NOTICE

The installation, maintenance, or removal of an antenna

requires qualified, experienced personnel. Andrew

installation instructions are written for such installation

personnel. Antenna systems should be inspected once a

year by qualified personnel to verify proper installation,

maintenance, and condition of equipment.

Andrew disclaims any liability or responsibility for the

󳣝

included with

DB380-3

Middle

pipe bracket

is truly vertical.

DB380/DB380-3 and DB5083/DB5083D Mounting Kits

Bulletin 095351-000 • Revision AE • July 2013 • Page 2 of 4

(Continued from page 1)

DB380/DB380-3 Pipe Mount Clamp.

Use inclinometer

to verify antenna

Attaching Antenna to a Mast Using DB380/DB380-3 Pipe Mount.

Bracket Without Tab

M12 Flat Washer

M12–1.75 X 190 Hex HD Bolt

M10 Split Lock Washer

M10–1.5 Hex HD Nut

Hex HD Bolt

M12–1.75 X 190

With Tabs

Bracket

Without Tabs

Bracket

Hex HD Nut

M12 Split Lock Washer

M12 Flat Washer

Antenna Bracket

M10–1.5 Hex HD Nut

M12–1.75

Lock Washer

M10 Split

Hex HD Nut

M12–1.75

Lock Washer

M12 Split

Washer

M12 Flat

Hex HD Bolt

M10–1.5 X 35 Hex HD Bolt

M10–1.5 X 35

Bracket With Tab

prior to attaching bracket to antenna.

ATTENTION: Insert M12 bolts and

M12 flat washers into bracket with tabs

ATTENTION

: Insert M12 bolts and

M12 flat washers into bracket with tabs

prior to attaching bracket to antenna.