Umbrella Specification Rev 5.02.1, based on ZVEI Layout, EPCOS AG, Dr. G. Schulz, Dept. TQ, 08/2014  EPCOS AG 2014 • Page 1/2

MKK Film Capacitor Material Data Sheet

Product Class Film capacitors B25673xx

Date 18/09/2014

IMDS ID

if available

Version 5.02.1 (08/2014)

Product Part

(IMDS: semi

component)

Material Class

(IMDS: Material)

Material

(Classification)

VDA 231

Substance

TMPS**)

[wt%]

CAS

if applicable

typical mass of

material

[wt-%]

Traces

see 1)

Active Part Thermoplastic 2A

100

9003

44 (if PA)

41 (if AL)

Heavy metal

Light Metal

440

7429-90-5

9.8

Light Metal or

Thermoplastic

Al or

Polyamide

(depending upon

specific type)

100

7429

5 or

628-02-4

1.4 (if Al)

2.7(if PA)

Thermoplastic 2A

Polyester

25038

Light Metal 1B

Silicon

7440

Encapsulation

Light metal 1B Al 100 7429-90-5 10

Thermoplastic 2A Polyamide 100 628-02-4 4

Duromer / Operating

supply

2D or 6G Polyurethane or N2 Gas 100 Not available /

7727-37-9

22.3

Termination Light Metal 1B Al

7429-90-5

7439-95-4

1.2

Thermoplastic 2A Polyamide 100 628-02-4 2

Heavy metal 1C Cu 100 7440-50-8 2.3

Organic solid 4B Adhesive and Sealers 100 …… 0.7

Iron & Steel 1A Fe 100 7439-89-6 1.8

Heavy metal 1C Sn

99.3

0.7

7440-31-5

7440-50-8

0.4

Mounting Part Iron & Steel 1A Fe 98 7439-89-6 0.3

Heavy metal 1C Zn 2

7440

Sum in total: 100

sizes [mm] weight range [.kg] sizes [mm] weight range [.kg] sizes [mm] weight range [.kg] sizes [mm] Weight range [.kg] Part Number

85x125 0.7 100x162 1.4 116x164 2.1 136x200 3.2 B25673

85x162 1.0 100x200 1.7 116x220 2.2

116x224 2.7

116x248 3.0

Not part of a Product Class

Contact Anant Marathe

mportant remarks:

1) The declaration limit is 0.1% as defined by IEC 62474 (IEC PAS 61906). Traces are

product parts, substances etc. that are below a percentage of 0.1 % by weight, if not

otherwise regulated

2) This Material Data Sheet contains typical values of the respective products set forth

herein. We expressly point out that all values and statements contained herein are

based on our best present knowledge and cannot be regarded as binding statements

or binding product specifications, unless otherwise explicitly agreed in writing. EPCOS

AG AND ITS AFFILIATES HEREBY EXPRESSLY DISCLAIM ANY

REPRESENTATION OR WARRANTY, WHETER EXPRESS, IMPLIED OR

STATUTORY, WITH REGARD TO THE STATEMENTS AND VALUES CONTAINED

HEREIN, INCLUDING BUT NOT LIMITED TO ANY REPRESENTATION OR

WARRANTY OF MERCHANTABILITY OR SUITABILITY FOR ANY PURPOSE.

Division PFC, R&D, FILM

Address Epcos India Pvt. Ltd., Plot E 22/25, MIDC, Satpur, Nashik -

422007, INDIA

Tel: +91 253 2205 117 mailto: anant.marathe@epcos.com

*) others: .(not declarable or prohibited substances acc. GADSL)

**) typical mass percentage of substance

The products set forth herein are “RoHS

compatible

”

RoHS-compatible means that products are compatible with the requirements according to Art. 4 (substance restrictions)

of Directive 2011/65/EU of the European Parliament and of the Council of June 8

, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic

equipment.

Umbrella Specification Rev 5.02.1, based on ZVEI Layout, EPCOS AG, Dr. G. Schulz, Dept. TQ, 08/2014  EPCOS AG 2014 • Page 2/2

RoHS

Exemptions for the Product Class / Product according to Annex III:

(  valid  not valid )

 no exemptions;

 Exemption 6 (a): Lead as an alloying element in steel for machining purposes and in galvanized steel containing up to 0,35 % lead by weight;

 Exemption 6 (b): Lead as an alloying element in aluminium containing up to 0,4 % lead by weight;

 Exemption 6 (c): Copper alloy containing up to 4 % lead by weight;

 Exemption 7 (a): Lead in high melting temperature type solder (i.e. lead-based alloys containing 85 % by weight or more lead);

 Exemption 7 (c)-I: Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound;

 Exemption 7 (c)-II: Lead in dielectric ceramic in capacitors for a rated voltage of 125 V AC or 250 V DC or higher;

 Exemption 7 (c)-III: Lead in dielectric ceramic in capacitors for a rated voltage of less than 125 V AC or 250 V DC;

 Exemption 15: Lead in solders to complete a viable electrical connection between semiconductor die and carrier within integrated circuit Flip Chip packages;

 Other Exemption than above ....................................................................