Oiles 600
Wear-resistant copper alloy bearings
Feature
Demonstrates wear resistance and seizure resistance in lubricated conditions.
Reduces the frequency of lubrication.
Demonstrates especially high running-in characteristics.
Materials for machining are available.
Relief angle
Rake angle
Nose radius
(
mm
)
Speed
(
m/min
)
Cut depth
(
mm
)
Feed
(
mm/rev
)
carbide tool
(
JIS
)
5∼10゜
2∼5゜
0.40∼0.80
100∼200
0.05∼0.30
0.08∼0.30
Lathe turning
Cutting toolCondition
I.D.
class 7 to 8
O.D.
class 6 to 7
Length
class 8 to 9
Machining accuracy (bushing)
Classes here are in JIS standard.
This product demonstrates satisfactory
performance at the slide surface roughness
of Rz6.3 to 12.5
μ
m.
※
The values shown above are typical values, not the standard values.
Service range
Lubrication condition
Service temperature range
℃
Allowable max. pressure
P
N/mm
2
{
kgf/cm
2
}
Allowable max. velocity
V
m/s
{
m/min
}
Allowable max.
PV
value
N/mm
2
・
m/s
{
kgf/cm
2
・
m/min
}
periodic lubrication
1.65{99}
1.65{1,010}
−40∼+150
15{153}
oil lubrication
5.00{300}
3.25{1,990}
Density
Tensile strength
Impact strength
Hardness
Modulus of longitudinal elasticity
Co-efficient of linear expansion
Thermal conductivity
̶
JIS Z 2241
JIS Z 2242
JIS Z 2243
̶
̶
̶
8.5
150{15}
10{1}
60
83,000{8,500}
1.8
71.1{0.17}
Mechanical properties
g/cm
3
N/mm
2
{kgf/mm
2
}
J/cm
2
{kgfm/cm
2
}
HBW
N/mm
2
{kgf/mm
2
}
×10
−5
℃
−1
W/m℃{cal/sec℃cm}
269
36M
Oiles 600 Bar Stock
36S
Oiles 600 Bushing Material
●
Length and diameter shown here are rough
finished dimensions.
●
Need to be oil-impregnated before use.
Inner and outer diameter and Length shown
here are rough finished dimensions.
Need to be oil-impregnated before use.
Part No.
L
16
21
26
31
36
41
46
51
56
61
202
202
202
202
202
202
202
202
202
202
36M-16
36M-21
36M-26
36M-31
36M-36
36M-41
36M-46
36M-51
36M-56
36M-61
0
0
0
0
0
0
0
0
0
0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
Tolerance
0
0
0
0
0
0
0
0
0
0
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
Tolerance
Diameter Length
φ
D
Part No.
I.D. O.D. Length
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Tolerance
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ToleranceTolerance
36S-1931
36S-1936
36S-2436
36S-2941
36S-2946
36S-3446
36S-3451
36S-3951
36S-3966
36S-4456
36S-4961
36S-4971
36S-5981
36S-6986
φ
d
φ
DL
19
19
24
29
29
34
34
39
39
44
49
49
59
69
31
36
36
41
46
46
51
51
66
56
61
71
81
86
202
202
202
202
202
202
202
202
202
202
202
202
202
202
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
−0.5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
L
φD
L
φd
φD
Specify Part No. by required diameter.
(e.g.) Diameter is 36mm.
Part No.
36M - 36
Specify Part No. by required I.D. and O.D.
(e.g.) I.D. is 34mm and O.D. is 51mm.
Part No.
36S - 3451
270