Oiles 80
Oil-impregnated polyacetal bearings
Feature
Serviceable without the need for lubrication.
Has superior load resistance and wear resistance.
Features low coecient of friction and superior speed characteristics.
Prevents stick slips and squeak noises.
Injection-molded and can be made in complicated shapes. Good mass
productivity.
Standard products and materials for machining are available in various sizes.
For a low volatile organic compound type, Oiles 80-LVF is available on order.
Image
Lubricating oil
Polyacetal
Specific gravity
Tensile strength
Tensile elongation at break
Flexural property
Flexural modulus
Hardness
Izod impact strength (with notch)
Co-efficient of linear expansion
Deflection temperature under load 1.82 MPa
Melting point
UL incombustibility
ASTM D 792
ASTM D 638
ASTM D 638
ASTM D 790
ASTM D 790
ASTM D 785
ASTM D 256
ASTM D 696
ASTM D 648
DSC
UL94
1.39
51.0{520}
60
76.5{780}
2,650{27,000}
21.1{215}
81.9{835}
72
58.8{6.00}
8∼13
110
165
HB
(Note)
Mechanical properties
Compressive stress
1% deformation
10% deformation
ASTM D 695
Service range
Lubrication condition
Service temperature range
℃
Allowable max. pressure
P
N/mm
2
{
kgf/cm
2
}
Allowable max. velocity
V
m/s
{
m/min
}
Allowable max.
PV
value
N/mm
2
・
m/s
{
kgf/cm
2
・
m/min
}
Dry
−40∼+80
17.5{179}
0.85{51}
2.45{1,500}
Relief angle
Rake angle
Nose radius
Speed
Cut depth
Feed
carbide tool
(
JIS
)
5∼10゜
10∼20゜
0.20∼0.40
100∼250
0.10∼0.50
0.05∼0.20
Lathe turning
(
mm
)
(
m/min
)
(
mm
)
(
mm/rev
)
Cutting toolCondition
I.D.
class 8 to 9
O.D.
class 7 to 8
Length
class 9 to 10
Machining accuracy (bushing)
Classes here are in JIS standard.
This product demonstrates satisfactory
performance at the slide surface roughness
of Rz6.3 to 12.5
μ
m.
Dimensions may change due to thermal
expansion, chucking pressure, moisture
absorption deformation, etc. High accuracy
is ensured if the product is installed on the
housing and then ground.
Attention should be paid to dimensional
variances due to thermal expansion,
chucking, and bend of the material.
※
Contact us for grinding and milling
information.
※
These are values of the typical grade Oiles 80.
※
The values shown above are typical values, not the standard values.
(
Note
)
Excludes 80M, 80P, 80S and 80-LVF.
̶
N/mm
2
{kgf/cm
2
}
%
N/mm
2
{kgf/cm
2
}
N/mm
2
{kgf/cm
2
}
N/mm
2
{kgf/cm
2
}
HRM
J/m{kgfcm/cm}
×10
−5
℃
−1
℃
℃
File No.E78113
Standard Material Custom-made
67
Test data
Journal rotation test
<Testing conditions>
Bearing dimension : φ3 5×φ3 8×R20
Pressure : 0.39N/mm
2
{4.0kgf/cm
2
} is
added every 5 minutes
Velocity : 1.133m/s{68.0m/min}
Lubrication : grease is applied at
the time of assembly
1.0
0.8
0.6
0.4
0.2
0
2.45
{25}
0 4.90
{50}
7.35
{75}
9.81
{100}
12.25
{125}
14.71
{150}
17.16
{175}
Wear amount〔mm〕
Pressure
〔 〕
N/mm
2
{kgf/cm
2
}
Sintered oil impregnated copper type bearing
Oiles 80
Nylon with MoS2
Journal oscillation test
<Testing conditions>
Bearing dimension : φ4 0×φ5 0×R30
Mating material : S45C
(surface roughness Rz1.5μm)
Pressure : 4.4N/mm
2
{45.0kgf/cm
2
}
Velocity : 0.02m/s{1.2m/min}
Oscillating cycle : 72cpm
Oscillating angle : 24°
Lubrication : grease is applied at
the time of assembly
0.4
0.3
0.2
0.1
0
20 4 6 8 10 12 14
Wear amount〔mm〕
Noise
Nylon with MoS2
Polyacetal resin+PTFE
Sliding distance〔×10
3
m〕
Noise
Oiles 80
Thrust rotation test
<Testing conditions>
Mating material : S45C
(surface roughness Rz3μm)
Pressure : 2.94N/mm
2
{30.0kgf/cm
2
}
Velocity : 0.167m/s{10.0m/min}
Test time : 50hrs.
Lubrication : dry
1.0
0.8
0.6
0.4
0.2
0
100 20304050
Coefficient of friction〔μ〕
Test time〔hrs.〕
Oiles 80
Nylon66
Polyacetal
0.068mm
0.056mm
0.031mm
Wear amount
W
W
W
Journal rotation test
<Testing conditions>
Bearing dimension : φ1 0×φ1 4×ℓ1 0
Mating material : SUJ2
(surface roughness approx. Ra0.1μm��
Pressure : 0.98N/mm2{10kgf/cm
2
}
Volocity : 0.17m/s{10m/min}
Test time : 50hrs.
Lubricataion : dry
0.007mm
0.007mm
1.0
0.8
0.6
0.4
0.2
0
10020304050
Coefficient of friction〔μ〕
Test time〔hrs.〕
Oiles 80
Oiles 80-LVF
W
Wear amount
68