Product Description Sheet
LOCTITE
®
FREKOTE FRP-NC
Known as
Frekote
®
FRP-NC
September 2015
Description
Loctite
®
Frekote
®
FRP-NC is a unique release interface
specifically formulated for reinforced polyester gel coats (and
other associated resin systems). This semi-permanent release
coating chemically bonds to the mold surface, forming a micro
thin release film. Loctite
®
Frekote
®
FRP-NC provides a high
gloss finish and minimal mold build-up thus eliminating buffing
and cleaning between applications. Multiple releases per
application also contributes to major time savings.
Features
Minimal mold build-up
Multiple releases per application
High gloss finish
Maximum mold utilization
Lower mold maintenance costs
Fast cure
Properties
Appearance Clear liquid
Odor Hydrocarbon
Solvents Aliphatic Hydrocarbon, Dibutyl Ether
Specific Gravity 0.770 +/- 0.010
Flash Point 28°C (82°F) Tag Closed Cup.
Shelf Life One year from date of manufacture
Special Cautions Moisture sensitive, keep container
tightly closed when not in use.
Application Temp 13ºC - 40ºC (55F - 105F)
Thermal Stability 400ºC (750°F)
Mold Preparation
To work effectively, Frekote Release products must be applied
to thoroughly cleaned and dried mold surfaces. All traces of
waxes, sealers, rubbing compounds or other release agents
must be completely removed. Remove any contaminants with
Frekote PMC, PMC Plus or suitable cleaning solvent. Light
industrial abrasives can be used to remove heavy resin build-
up.
Mold Sealing
New Molds: Full curing of new molds is advisable to ensure the
best bonding of the Frekote to the mold surface. New
fiberglass and epoxy molds should be cured per manufacturer’s
instructions before starting full-scale production.
Green molds and recently repaired areas must be sealed with
Frekote FMS prior to using Frekote releasing interfaces.
Porous and damaged mold surfaces should also be sealed with
FMS. Consult FMS Technical Data Sheet for specific
application instructions.
Application *Consult MSDS Prior To Use.*
1. Apply with a clean lint free 100% cotton cloth. Soak cloth
with Loctite
®
Frekote
®
FRP-NC until it is wet, but not
dripping.
2. Wipe a smooth, wet film over a 2' x 2' to 2' x 3' area of the
mold surface. Do not over apply.
3. Wait 10-20 seconds at 21ºC (70°F) after application.
Gently wipe dry with, a second clean dry, cotton cloth.
NOTE: Changes in temperature will affect solvent dry time.
At temperatures below 18ºC (65°F), waiting time between
wiping on and drying off will be longer than 20 seconds. A
general guideline is to wait until the edges of the wiped
area begin to creep inwards indicating that evaporation has
progressed sufficiently. Light hand pressure is all that is
needed. No hard rubbing is required. Change cloth
frequently to ensure proper drying of the mold.
4. Coat entire mold surface in this manner slightly over-
lapping the last area coated. Apply a maximum of 6 coats
initially. A couple of extra coats can be applied in high
wear areas for added slip. Allow 15-20 minutes cure time
at room temperature between coats and after the final coat.
5. Commence molding. A single coat of Loctite
®
Frekote
®
FRP-NC should be applied after each release for the first
two to three releases. This helps to condition the mold,
which in turn offers multiple releases on future production.
Mold Touch up
Abrasion will gradually cause wear and parts will begin to
adhere to the mold surface if a continuous release film is not
maintained. If release becomes difficult, simply touch-up the
area affected. Only one coat is usually required for touch-up.
Use either Loctite
®
Frekote
®
FRP-RS or Loctite
®
Frekote
®
FRP-
NC for touch-ups.
Flammability/Storage
Loctite
®
Frekote
®
FRP-NC contains flammable solvents. The
product should always be used in well-ventilated areas. Store
in a cool, dry place. Consult MSDS for complete details.
Note
The information provided in this Technical Data Sheet (TDS) including
the recommendations for use and application of the product are based
on our knowledge and experience of the product as at the date of this
TDS. The product can have a variety of different applications as well as
differing application and working conditions in your environment that are
beyond our control. Henkel is, therefore, not liable for the suitability of
our product for the production processes and conditions in respect of
which you use them, as well as the intended applications and results.
Product Description Sheet
LOCTITE
®
FREKOTE FRP-NC
Known as
Frekote
®
FRP-NC
September 2015
We strongly recommend that you carry out your own prior trials to
confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or
any other written or oral recommendation(s) regarding the concerned
product is excluded, except if otherwise explicitly agreed and except in
relation to death or personal injury caused by our negligence and any
liability under any applicable mandatory product liability law.
In case products are delivered by Henkel Corporation, Resin
Technology Group, Inc., or Henkel Canada, Inc.the following disclaimer
is applicable:
The data contained herein are furnished for information only and are
believed to be reliable. We cannot assume responsibility for the results
obtained by others over whose methods we have no control. It is the
user's responsibility to determine suitability for the user's purpose of
any production methods mentioned herein and to adopt such
precautions as may be advisable for the protection of property and of
persons against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including warranties
of merchantability or fitness for a particular purpose, arising from
sale or use of Henkel Corporation’s products. Henkel Corporation
specifically disclaims any liability for consequential or incidental
damages of any kind, including lost profits. The discussion herein of
various processes or compositions is not to be interpreted as
representation that they are free from domination of patents owned by
others or as a license under any Henkel Corporation patents that may
cover such processes or compositions. We recommend that each
prospective user test his proposed application before repetitive
use, using this data as a guide. This product may be covered by one or
more United States or foreign patents or patent applications.
In case products are delivered by Henkel Belgium NV, Henkel
Electronic Materials NV, Henkel Nederland BV, Henkel Technologies
France SAS and Henkel France SA please additionally note the
following:
In case Henkel would be nevertheless held liable, on whatever legal
ground, Henkel’s liability will in no event exceed the amount of the
concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the
following disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including
the recommendations for use and application of the product are based
on our knowledge and experience of the product as at the date of this
TDS. Henkel is not liable for the suitability of our product for the
production processes and conditions in respect of which you use them,
as well as the intended applications and results. We strongly
recommend that you carry out your own prior trials to confirm such
suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or
any other written or oral recommendation(s) regarding the concerned
product is excluded, except if otherwise explicitly agreed and except in
relation to death or personal injury caused by our negligence and any
liability under any applicable mandatory product liability law.
Trademark usage
Except as otherwise noted, all trademarks in this document are
trademarks of Henkel Corporation in the U.S. and elsewhere. ®
denotes a trademark registered in the U.S. Patent and Trademark
Office.