TROLLEY JACK 3TONNE

MODEL NO: 3290CX

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

  Ensure the jack is in sound condition and good working order. Take action for immediate repair or

replacement of damaged parts. Use recommended parts only. The use of improper parts may be

dangerous and will invalidate the warranty.

  Locate the jack in an adequate, well lit working area for its function.

  Keep working area clean and tidy and free from unrelated materials.

  Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as the jack may sink in.

  Place wedges under wheels of vehicle (but ensure wheels of jack can move freely ).

  Ensure the vehicle handbrake is engaged (or in “PARKED” mode), and switch the engine off.

 Ensure minimum distance of 0.5m between vehicle tilt & static objects such as doors, walls, etc.

 Ensure all non essential persons keep a safe distance whilst the jack is in use.

 Ensure there are no passengers in the vehicle to be jacked up.

 Place jack under vehicle manufacturer’s recommended lifting points (see vehicle hand book).

 Check that the lifting point is stable and centred on the jack saddle.

  Ensure the jack wheels are free to move and that there are no obstructions.

 WARNING: The jack is a lifting device only.

  To support the load always use axle stands (available from your Sealey stockist).

  Ensure there are no persons or obstruction beneath the vehicle before lowering.

 Use a competent person to lubricate and maintain the jack.

  Use only hydraulic jack oil during maintenance.

  When not in use store jack in a safe, dry, child proof area in the lowered position.

  DO NOT jack vehicle which may result in spillage of fuel, battery acid, or dangerous substances.

8 88 DO NOT work under the vehicle until axle stands have been correctly positioned.

8 88 DO NOT operate the jack if damaged.

8 88 DO NOT adjust the safety overload valve.

8 88 DO NOT exceed the rated capacity of the jack.

8 88 DO NOT allow the vehicle to move whist lifting or lowering.

8 88 DO NOT use the jack for purposes other than which it is intended.

8 88 DO NOT use the jack to move vehicle.

8 88 DO NOT top up the hydraulic unit with brake fluid. Use hydraulic oil only.

8 88 DO NOT allow untrained persons to operate the jack.

2. INTRODUCTION

Single-piece hydraulic unit. Integral American cog-type release mechanism and long two-piece handle to reduce operator effort. Heavy-duty

castors and large saddle design ease positioning under vehicle. Fitted with safety overload valve and pump-through valve to prevent handle locking

at maximum ram extension. Under 30kg Gross weight for easier transportation and manoeuvrability.

3. SPECIFICATION

Model no ................................................................... 3290CX

Capacity ......................................................... 3tonne/3000kg

Minimum saddle height .............................................. 130mm

Maximum saddle height ............................................. 465mm

Maximum chassis height ............................................ 175mm

Length ........................................................................ 572mm

Weight ............................................................................ 28kg

4. ASSEMBLY

4.1. Line up the holes in the two piece handle and fasten with the assembly screw.

4.2. Loosen location bolt at the side of the handle base. Insert jack handle and tighten the bolt.

Refer to

instruction

manual

Wear

protective

footwear

3290CX | Issue:3 (1,7) 08/06/18

Original Language Version

Apply

Chock

Wheels

Never

exceed

Original Language Version

5. OPERATION Before first ue.

5.2.1. Before using the jack, purge hydraulic circuit in order to eliminate any possible air in the

system by turning the handle anti-clockwise to open the release valve and pumping

15 to 20 times (fig.1). At the end of the last downward stroke shut the valve off again by

turning the handle clockwise.

5.1. General.

5.2. WARNING! Before lifting ensure section 1 safety instructions are strictly followed.

5.2.1. Prepare the vehicle as mentioned in the safety instructions ensuring the ground on which

the jack is to stand is level and solid (not tarmacadam).

5.2.2. Position the jack saddle under the vehicle manufacturer’s recommended lifting point.

5.3. Jacking the vehicle.

5.3.1. Turn the handle clockwise to close the valve and commence pumping the handle up and down using maximum strokes until the vehicle

reaches the desired working height.

5.3.2. Should the jack become overloaded, a safety excess pressure valve will open, and stop the jack from lifting.

5.4. Weight Distribution

5.4.1. Up to 80% of the lifted load is carried by the front jack wheels placing exceptional stress on the point of contact with the floor. For this

reason use on a hard level concrete surface only.

5.5. Lowering the Load

5.5.1. The lowering speed is controlled by the amount the handle is turned. Lower slowly and carefully, avoiding sudden release.

 WARNING! Ensure there are no persons or obstacles beneath the vehicle, or in the path of its descent.

6. MAINTENANCE

IMPORTANT: Only competent personnel should attempt maintenance or repair.

6.1. When the jack is not in use, the ram and the handle socket should be in their lowest position

to minimise corrosion. Remove the handle to deactivate jack.

6.2. Keep the jack clean and lubricate all moving parts with lubricating oil on a regular basis.

6.3. To check the oil level, fully lower the jack. Remove oil plug (fig.2). The correct oil level should

be approximately 5mm below the filler opening. If oil level is low, fill as required.

Pump unloaded jack 15 to 20 times to expel air and then refit plug.

NOTE: Use a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL.

 WARNING: DO NOT use brake fluid, or any fluid other than hydraulic jack fluid as this may cause serious damage to the jack

and will invalidate the warranty!

6.4. Before each use check for broken, cracked, bent, or loose parts, or any visible damage to welds, ram, pump, saddle, lifting arm,

frame and all parts including nuts, bolts, pins and other fasteners. If any suspect item is found remove jack from service and take

necessary action to remedy the problem. DO NOT use the jack if believed to have been subjected to abnormal load or shock.

6.5. Inspect and take appropriate action.

6.6. Every three months remove the locking rings on the caster wheels and lubricate the ball bearings with grease.

6.7. After a year of extensive use, the oil should be replaced in order to extend the life of your jack. To drain the oil, remove the oil plug

and valve. Make sure that no dirt is allowed to enter the hydraulic system’s oil. Dispose of oil according to local authority regulations. See

6.3. for refill instructions.

6.8. Check the pump piston and piston rod periodically for signs of corrosion. Clean exposed areas with a clean oiled cloth.

IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE JACK.

Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.

DO NOT RETURN JACKS TO US. Please telephone us on 01284 757500 to obtain the address and phone number of your local agent.

If Jack is under guarantee please contact your dealer.

fig.

3290CX | Issue:3 (1,7) 08/06/18