Thank you for purchasing the
LSI SAS 9302-16e Host Bus Adapter
(HBA). Please take a few minutes to
read this quick installation guide
before you install the HBA.
For more information about any
topic covered in this guide, refer to
the documents listed with your
product at the following link:
http://go.lsi.com/hbas
ATTENTION: Perform all installation work at
an electrostatic discharge (ESD)-
safe workstation that meets the
requirements of EIA-625.
Requirements for Handling
Electrostatic Discharge Sensitive
Devices
. You must perform all
actions in accordance to the
latest revision of the IPC-A-610
ESD-recommended practices.
Quick Installation Guide
LSI
®
SAS 9302-16e PCI Express
®
to 12Gb/s SAS Host Bus Adapter
55635-00001
To install the LSI
®
12Gb/s SAS HBA, follow these steps:
1. Unpack the HBA, and inspect it for damage. Unpack the HBA in a static-free environment.
Remove the HBA from the antistatic bag, and carefully inspect the device for damage. If you notice any
damage, contact Avago or your reseller support representative.
ATTENTION: To avoid the risk of data loss, back up your data before changing your system configuration.
2. Prepare the computer. Turn off the computer, and disconnect the power cord from the rear of the
power supply.
CAUTION: Disconnect the computer from the power supply and from any networks to which you
will install the HBA, or you risk damaging the system or experiencing electrical shock.
3. Remove the cover from the chassis.
4. Insert the HBA into an available PCIe
®
slot. Locate an empty x16 PCIe slot. Remove the blank
bracket panel on the rear of the computer that aligns with the empty PCIe slot. Save this bracket screw, if
applicable. Align the HBA to a PCIe slot. Press down gently, but firmly, to seat the HBA correctly in the
slot. The following figure shows how to insert the HBA into a PCIe slot.
NOTE: The shape, size, and locations of the components on your HBA and its bracket might vary from
this illustration. The HBA requires a x16 PCIe slot.
5. Secure the HBA bracket to the system’s chassis. Install the bracket screw, if applicable, or engage
the system retention mechanism to secure the HBA to the system’s chassis.
6. Connect the auxiliary power cable to the LSI SAS 12Gb/s SAS HBA if auxiliary power is
required with your system design.
7. Replace the cover of the chassis.
8. Connect SAS cables between the HBA and the SAS enclosure that contains SATA or SAS
devices. The LSI 12Gb/s SAS HBA has four SFF-8644, external x4, mini-SAS HD connectors. Use a cable
with an external mini-SAS HD connector (SFF-8644) on one end (to connect to the HBA) and the
appropriate connector to attach to the enclosure that contains SAS or SATA devices on the other end.
The hardware installation of your LSI 12Gb/s SAS HBA is complete.
?
%DGEOF(OST"OARD
0#)%XPRESSX3LOT
"RACKET
3CREW
0RESS
(ERE
0RESS
(ERE
4O$RIVE
%NCLOSURES
-INI3!3($
%XTERNAL
#ONNECTORS
TECHNICAL SUPPORT
For assistance installing, configuring, or running
the LSI SAS 9302-16e HBA, contact Technical
Support:
WARRANTY NOTICE
1. Warranty does not cover the return of parts
damaged by changing the bracket.
2. Warranty does not cover ESD damage to the
HBA. HBAs returned without a bracket mounted
on the board will be returned without return
merchandise authorization (RMA) processing.
E-mail: globalsupport.pld@avagotech.com
Web Site: http://www.lsi.com/support/email/
pages/sashba.aspx
Avago, Avago Technologies, the A logo, LSI, Storage by LSI are trademarks of Avago Technologies in the United States and/or other countries. All other
brand and product names may be trademarks of their respective companies.
Corporate Headquarters Email Website
San Jose, CA globalsupport.pdl@avagotech.com www.lsi.com
Document Number: 55635-00001
Copyright © 2015 Avago Technologies
All Rights Reserved. February 2015.
Driver Installation
All driver installation instructions are available at http://go.lsi.com/hbas. Select 12Gb/s SAS HBAs >
Product Name > Software Downloads.