www.FraenOMG.com 1/8 FCP Series for Cree XLamp XB-D, Rev 00

FCP Lens Series

for Cree XLamp XB-D

LEDs

 High efficiency design

 5 beams patterns available

 Available as a lens alone for

maximum design flexibility or

in a holder for easy assembly

The FCP lens offers low profile lenses specifically

designed for the XLamp XB-D LEDs from Cree

Corporation.

A software-optimized aspheric profile enables the

generation of several different beam output

patterns: narrow, medium, wide, medium elliptical

and wide elliptical beams

The design of the FCP series insures that almost

all of the light emitted by the LED is captured and

usefully directed, resulting in a lens with maximum

performance and efficiency.

Lens holders are available in black, white or

transparent polycarbonate to provide the proper

alignment between the LEDs and the lenses; and

to set the correct distance between the lens and

LED.

The lens holder can be glued and/or screwed to

the PCB to provide a secure assembly.

Typical applications are:

 Reading lamps

 Architectural lighting

 Entertainment lighting

 Interior lighting

 Portable lighting

(1) Cree® XLamp is a trademark of Cree, Inc. For

technical information about these LEDs, please

refer to the Cree® XLamp datasheet or visit:

www.cree.com.

(2) Typical beam divergence may vary with LED color

FRAEN Corporation OMG FRAEN Corporation Srl

80 Newcrossing Road Via delle Querce, 22

Reading MA 01867 27020 Trivolzio (PV)

USA Italy

Phone: +1 781.205.5300 Phone: +39 0382 1933.1

Fax: +1 781.942.2426 Fax: +39 0382 1933.239

Inquiries: optics@fraen.com

Website: FraenOMG.com

For ordering or sales information in your region,

please contact one of our offices listed above or

visit www.FraenOMG.com/Contact.

www.FraenOMG.com 2/8 FCP Series for Cree XLamp XB-D, Rev 00

General Characteristics

Materials

Lens Material Optical Grade PMMA

Holder Material Polycarbonate: Clear

Operating Temperature range -40° C / + 80° C

Storage Temperature range -40° C / + 80°C

Average transmittance in visible spectrum (400 – 700nm) >90%, as measured using

3mm thick Optical Grade PMMA.

Please note that flow lines and weld lines on the external surfaces of the lenses are

acceptable if the optical performance of the lens is within the specification described in

the section “OPTICAL CHARACTERISTICS”

IMPORTANT NOTE – Lenses handling and cleaning:

 Handling: Always use gloves to handle lenses and/or handle the lenses only by

the flange. Never touch the outside surfaces of the lenses with fingers; finger oils

and contamination will absorb or refract light.

 Cleaning: Clean lenses only if necessary. Use only soap and water to clean the

surfaces and lenses. Never expose the lenses to solvents such as alcohol, as it

will damage the plastic.

Scope

This datasheet provides information about the FCP lens series for Cree XLamp LEDs.

Lens alone:

 FCP-N1-XPE1-0R

 FCP-M1-XPE1-0R

 FCP-W1-XPE1-0R

 FCP-E1-XPE1-0R

 FCP-E2-XPE1-0R

Lens Assemblies (lenses in holders):

Black Holder White Holder Transparent Holder

 FCP-N1-XPE1-HRF FCP-N1-XPE1-HRFW FCP-N1-XPE1-HRFT

 FCP-M1-XPE1-HRF FCP-M1-XPE1-HRFW FCP-M1-XPE1-HRFT

 FCP-W1-XPE1-HRF FCP-W1-XPE1-HRFW FCP-W1-XPE1-HRFT

 FCP-E1-XPE1-HRF FCP-E1-XPE1-HRFW FCP-E1-XPE1-HRFT

 FCP-E2-XPE1-HRF FCP-E2-XPE1-HRFW FCP-E2-XPE1-HRFT