7669E-AVR-04/14
This document contains information specific to devices operating at voltage between 1.8V
and 3.6V. Only deviations with standard operating characteristics are covere d in this
appendix, all other information can be found in the comple te Automotive datasheet. The
complete ATtiny25/ATtiny45/ATtiny85
automotive datasheet can be found on
http://www .atmel.com
ATtiny25/ATtiny45/ATtiny85
Appendix B - Automotive Specification at 1.8V
DATASHEET
ATtiny25/ATtiny45/ATtiny85 [DATASHEET]
7669E–AVR–04/14
2
1. Electrical Characteristics
1.1 Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functi onal operation of the device at these or any othe r conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Parameters Min. Typ. Max. Unit
Operating temperature –55 +150 °C
Storage temperature –65 +175 °C
Voltage on any pin except RESET with
respect to ground
–0.5 V
CC
+ 0.5 V
Volt age on RESET with respect to ground –0.5 +13.0 V
Maximum operating voltage 6.0 V
DC current per I/O pin 30.0 mA
DC current V
CC
and GND pins 200.0 mA
1.2 DC Characteristics
T
A
= –40°C to +85°C, V
CC
= 1.8V to 3.6V (unless otherwise noted)
Parameter Condition Symbol Min. Typ. Max. Unit
Input low voltage, except
XTAL1 and RESET pin
V
CC
= 1.8V - 3.6V V
IL
–0.5 0.2V
CC
(1)
V
Input high voltage, except
XTAL1 and RESET
pins
V
CC
= 1.8V - 3.6V V
IH
0.7V
CC
(2)
V
CC
+ 0.5 V
Input low voltage,
XTAL1 pin
V
CC
= 1.8V - 3.6V V
IL1
–0.5 0.1V
CC
(1)
V
Input high voltage,
XTAL1 pin
V
CC
= 1.8V - 3.6V V
IH1
0.9V
CC
(2)
V
CC
+ 0.5 V
Input low voltage,
RESET
pin
V
CC
= 1.8V - 3.6V V
IL2
–0.5 0.2V
CC
(1)
V
Input high voltage,
RESET pin
V
CC
= 1.8V - 3.6V V
IH2
0.9V
CC
(2)
V
CC
+ 0.5 V
Input low voltage,
RESET
pin as I/O
V
CC
= 1.8V - 3.6V V
IL3
–0.5 0.3V
CC
(1)
V
Input high voltage,
RESET
pin as I/O
V
CC
= 1.8V - 3.6V V
IH3
0.6V
CC
(2)
V
CC
+ 0.5 V
Output low voltage
(3)
,
I/O pin except RESET
I
OL
= 0.5mA, V
CC
= 1.8V V
OL
0.4 V
Notes: 1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (0.5mA at V
CC
= 1.8V) under steady state conditions (non-
transient), the following must be observed:
1] The sum of all IOL, for ports B0 - B5, should not exceed 50mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current
greater than the listed test condition.
4. Although each I/O port can source more than the test conditions (0.5mA at V
CC
= 1.8V) under steady state conditions
(non-transient), the following must be observed:
1] The sum of all IOH, for ports B0 - B5 should not exceed 50mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.