Installation Instructions for CS Series
Linear Current Sensor Holder Assemblies
GENERAL INFORMATlON
CS Series current sensor holder assem-
blies have a single linear output that will
source current. The output voltage, which is
ratiometric, varies in direct proportion to the
supply voltage. (Refer to Catalog 20 for
more information). These sensors will not
be damaged by overcurrent in the sensed
conductor.
NORMAL MOUNTlNG
Bottom mount version:
0.375 inch long 4-40 screw and a square
nut (not provided) inserted in the housing.
Side mount version:
0.250 inch long 6-32 screw and a square
nut (not provided) inserted in the housing.
SOLDERING INSTRUCTIONS
Hand Soldering
-
Use 60/40 rosin core
solder, employing a 399°C (750°F)
controlled temperature, 1/8" chisel tip
soldering iron. To avoid delamination of the
terminals from the ceramic, do not hold the
iron on the terminals for more than four
seconds. The temperature of the lead at the
ceramic conductor interface must not
exceed 250°C (482°F).
Wave Soldering
-
Use Loncoflux 106A35
or equivalent. Preheaters should be set for
95°C (200°F) on top (component side) of
printed circuit board just prior to board
entering wave. (This may have to be
adjusted depending upon board thickness.)
Solder temperature should be a maximum
of 260°C (500°F), preferably 252°C to 260°C
(485°F to 500°F). Set conveyor speed to
approximately 4.5 feet per minute (1,37
PK 87914
meter/min.). Select a speed which gives full
solder fillets and minimum of bridging and
icicles. The printed circuit board requires
rigid support during wave soldering.
CLEANING
Proper cleaning fluids should be selected
based on the type of contaminants to be
removed. HONEYWELL recommends
alcohols, chlorinated solvents, and
fluorinated solvents.
Electrical-
Do not exceed maximum supply
ratings. Do not reverse supply voltage
polarity.
Handling
-The terminals are fragile.
Handle with care.
Dielectric Isolation-
The toroidal cores are
conductive. The user must provide the
necessary dielectric isolation.
MOUNTING DIMENSIONS
(for reference only)
WARRANTY/REMEDY
Seller warrants its products to be free from defects in design,
material and workmanship under normal use and service. Seller will
repair or replace without charge any such product it finds to be so
defective on its return to Seller within 18 months after date of
shipment by Seller.
The foregoing is in lieu of all other ex-
pressed or implied warranties (except of title), including those
of merchantability and fitness for a particular purpose.
The
foregoing is also purchaser's sole remedy and is in lieu of all other
guarantees, obligations, or liabilities or any consequential,
incidental, or punitive damages attributable to negligence or strict
liability, all by way of example.
For application assistance, current specifications or technical help,
call toll free 800/537-6945.
While we provide assistance on HONEYWELL products,
personally and through our literature, it is up to the customer to
determine the suitability of the product in the application.
Honeywell Sensing & Control
CS Series Linear Current Sensor Holder Assemblies
PK 87914
OPERATING CHARACTERISTICS
BOTTOM MOUNT WITH 9SS (LOHET I) SENSOR
Core
Mtg.
Supply Supply
Sensed
Offset
Temp.
Offset Response
Catalog
Gap
Dim.
Voltage Current
Current* Voltage
Range
Shift Time
Listing
(in.)
Fig.
(DC)
(mA max.) (Amps-Peak) (V ± 10%)
°C
(%/°C)
(µS)
CSLA1CD
0.075 1 8 to
16 19
57
Vcc/2
-25
to
+85 ± 0.05 3
CSLA1CE
0.094
1
8 to
16 19
75
Vcc/2
-25
to
+85 ± 0.05 3
CSLA1DE
0.094
2
8 to
16 19
75
Vcc/2
-25
to
+85 ± 0.05 3
CSLA1CF
0.125 1
8 to 16
19
100
Vcc/2
-25 to +85
± 0.05 3
CSLA1DG
0.149 2
8 to 16
19
120
Vcc/2 -25 to +85
± 0.05
3
CSLA1CH
0.188 1
8 to 16
19
150
Vcc/2
-25 to +85
± 0.05
3
CSLA1DJ
0.276 2
8 to 16
19
225
Vcc/2 -25 to +85
± 0.05 3
CSLA1EJ
0.276 3
8 to 16
19
225
Vcc/2
-25 to +85
± 0.05 3
CSLA1DK 0.375 2
8 to 16
19
325
Vcc/2
-25 to +85
± 0.05 3
CSLA1EK 0.375 3
8 to 16
19
325
Vcc/2 -25 to +85
± 0.05 3
CSLA1EL 0.590 3
8 to 16
19
625
Vcc/2 -25 to +85
± 0.05 3
BOTTOM MOUNT WITH SS9 (LOHET II) SENSOR
Catalog
Listing
CSLA2CD
Core
Mtg.
Gap
Dim.
(in.)
Fig.
0.075 1
Supply
Voltage
(DC)
6 to 12
Supply
Sensed
Offset
Current Current* Voltage
(mA max.) (Amps-Peak) (V ± 2%)
20 72
Vcc/2
Temp.
Range
°C
-25 to +85
Offset
Shift
(%/°C)
± 0.02
Response
Time
(µS)
3
CSLA2CE
0.094 1
6 to 12
20 92
Vcc/2
-25 to +85
± 0.02 3
CSLA2DE
0.094 2
6 to 12 20
92
Vcc/2
-25 to +85
± 0.02 3
CSLA2CF 0.125 1
6 to 12
20
125
Vcc/2 -25 to +85
± 0.02 3
CSLA2DG
0.149 2
6 to 12
20 150
Vcc/2 -25 to +85
± 0.02 3
CSLA2DH
0.125 2
6 to 12 20 235
Vcc/2
-25 to +85
± 0.0125
3
CSLA2DJ
0.266 2 6 to 12
20
225 Vcc/2
-25 to +85
± 0.02 3
CSLA2EJ
0.160 3
6 to 12 20 310
Vcc/2
-25 to +85
± 0.0125 3
CSLA2DK
0.210 2
6 to 12
20
400
Vcc/2
-25 to +85
± 0.0125 3
CSLA2EL
0.276 3
6 to 12
20
550
Vcc/2
-25 to +85
± 0.0125 3
CSLA2EM
0.160 3
6 to 12
20
765
Vcc/2
-25 to +85
± 0.008 3
CSLA2EN
0.210 3
6 to 12 20 950
Vcc/2
-25 to +85
± 0.008 3
SIDE MOUNT WITH 9SS (LOHET I) SENSOR
Catalog
Listing
CSLA1GD
Core
Mtg.
Gap
Dim.
(in.)
Fig.
0.075 4
Supply
Voltage
(DC)
8 to 16
Supply
Sensed
Offset Temp.
Offset Response
Current Current*
Voltage Range
Shift Time
(mA max.) (Amps-Peak) (V ± 10%) °C
(%/°C)
(µS)
19
57
Vcc/2 -25 to +85
± 0.05
3
CSLA1GE
0.094
4
8 to 16
19
75
Vcc/2
-25
to
+85 ± 0.05 3
CSLA1GF 0.125
4
8 to 16
19
100
Vcc/2
-25
to
+85 ± 0.05 3
SIDE MOUNT WITH SS9 (LOHET II) SENSOR
Core
Mtg.
Supply
Supply
Sensed Offset Temp. Offset Response
Catalog
Gap
Dim.
Voltage
Current
Current*
Voltage Range Shift
Time
Listing
(in.)
Fig.
(DC)
(mA max.) (Amps-Peak) (V ± 2%)
°C
(%/°C)
(µS)
CSLA2GD
0.075
4
6 to 12
20
72 Vcc/2
-25
to
+85
± 0.02
8
CSLA2GE
0.094
4
6 to 12 20 92 Vcc/2
-25
to
+85
± 0.02
8
CSLA2GF 0.125
4
6 to 12 20
125
Vcc/2
-25
to
+85 ± 0.02 8
CSLA2GG
0.149
4
6 to 12
20 150
Vcc/2
-25
to
+85 ± 0.02 8
NOTE:
When monitoring purely AC current with zero DC component, a capacitor can be inserted in series with the output of the current sen-
sor. The capacitor will block out the effect of the temperature variation of the offset voltage which increases the accuracy of the device.
Honeywell Sensing & Control
Helping you control your world
PK 87914 293 Printed in USA