• Wear rubber-soled shoes and work on a sturdy ladder.

• This fixture must be installed according to the National Electric Code and local building

codes.

• To avoid a hazard to children, account for all parts and destroy all packing materials.

• To reduce the risk of fire and electrical shock, use only fixtures and fittings intended

for use with “LF”, “LA”, “L”, “LJ” and “LL” series track.

• Do not install in damp or wet locations.

• Do not install luminaire assembly closer than 6 inches from any curtain or similar

combustible material.

• Read carefully for your protection and save all instructions.

Installation Instructions for L805/806/807, LJ805/806/807

LL805/806/807

, LF805 and LA805 Series Fixtures

HALO

´L´ Connectors

age 1

Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • 770.486.4800 • FAX 770.486.4801 CLP-0001288-rev2 704732INS

Keep away from ﬂammable

apors or materials.

Risk of Burn

isconnect power and

llow ﬁxture to cool

before handling ﬁxture.

Risk of Electric Shock

isconnect power at fuse

r circuit breaker before

installing or servicing.

Risk of Fire/Electric

Shock

f not qualiﬁed, consult an

lectrician.

Service

For service questions contact point of purchase.

Installation Instructions for Halo Flexible Track (‘LF’ Series)

To Install Unit on Track (Fig 1):

Step 1.

Open CONNECTOR COVER by pulling downward on the CONNECTOR SLEEVE and

raising CONNECTOR COVER (Fig. 1).

Step 2. Hang unit on the TRACK so the CONTACTS are facing the intended circuit. 120V units

have 2 circuit options. 12V version has 1 circuit.

Note: For 120V Units - To access the other circuit, rotate the unit 180°.

Step 3. Move CONNECTOR into position and close CONNECTOR COVER until it snaps into

position.

To Remove Unit from Track:

Note: Allow unit to cool before removing from the track.

Step 1. Open CONNECTOR COVER by pulling downward on the CONNECTOR SLEEVE and

raising CONNECTOR COVER.

Step 2. Remove unit from track.

Installation Instructions for Halo Power-Trac ('L' Series), Lazer Track ('LZR' Series), Juno Track ('LJ' Series) and

Lightolier Track ('LL' series)

To Adjust Adapter (Fig 2A & 2B):

'L' units can be used with Lazer Track, Halo Single Circuit

Trac and Halo-2 Two Circuit Trac. 'LJ' units can be used

with Juno T Single Circuit and TU two circuit Trac. 'LL'

units can be used with Lightolier Lytespan Single Circuit

6000 series and two circuit Trac 6100 series. An

adjustable contact allows you to select circuit position.

Use a narrow blade screwdriver to adjust the contact. Lift

or lower the contact until it touches the plastic stop of the

contact assembly.

For Lazer, Halo Single Circuit and circuit #1 of Halo-2, 'L'-

track contact must be in down position (Fig. 2A). For

Halo-2 circuit #2, move contact to up position (Fig. 2B).

'LJ'- For Juno T single circuit and circuit #1 of TU, track

contact must be in down position (Fig. 2C). For Juno TU -

2 circuit #2, move contact to up position (Fig. 2D).

'LL'- For Lightolier Lytespan 6000 single circuit and circuit

#1 of Lytespan 6100, track contact must be in down posi-

tion (Fig. 2E). For Juno TU - 2 circuit #2, move contact to

up position (Fig. 2F).

FIG. 1

120V Units

CONNECTOR

SLEEVE

ONNECTOR

OVER

TRACK

CONTACTS

FIG. 2B

CIRCUIT NO. 2

(UP)

FIG. 2A

CIRCUIT NO. 1

(DOWN)

FIG. 2D

CIRCUIT NO. 2

(UP)

FIG. 2C

CIRCUIT NO. 1

(DOWN)

FIG. 2F

CIRCUIT NO. 2

(UP)

FIG. 2E

CIRCUIT NO. 1

(DOWN)

1. Juno

T single circuit and 2 circuit track contact. Juno is a registered trademark of Juno Lighting.

2. Lightolier

Lytespan 6000 single circuit and 2 circuit track contact. Lightolier is a registered trademark of Philips Lighting.

To Install Unit on Track (Figs 2G & 2H):

Step 1. Insert CONTACT HEAD into track.

tep 2.

Locate POLARITY GROOVE on adapter and TRACK POLARITY LINE.

Twist mounting adapter approximately 1/4 turn (90°) until it locks into track

opening and POLARITY GROOVE on adapter aligns with TRACK

POLARITY LINE (Figs. 2G & 2H).

Note: Forcing the mounting adapter in the wrong direction may damage the

contact assembly. If mounting adapter will not turn easily, twist adapter in

the opposite direction. POLARITY GROOVE on adapter must align with

TRACK POLARITY LINE for proper installation. When correctly installed,

RELEASE BUTTON will be beneath track opening (Fig. 2H).

To Remove Unit from Track:

Note:

Allow unit to cool before removing from track.

Step 1. Depress RELEASE BUTTON and twist mounting adapter 1/4 turn (90°)

until CONTACT HEAD is free (Fig. 2G).

Step 2. Remove fixture from track.

Installation Instructions for Halo Architectural Track (‘LA’ Series)

To Install Unit on Track (Fig 3):

Step 1.

Open SWITCH COVER so contacts are concealed inside adapter. Insure

SWITCH is in the ‘off’ position.

Step 2. Insert fixture into TRACK so contacts engage the desired circuit.

Note: To access the other track circuit, rotate fixture adapter 180°.

Step 3. Close SWITCH COVER and depress SWITCH to the ‘on’ position.

To Remove Unit from Track:

Note: Allow unit to cool before removing from TRACK.

Step 1. Depress SWITCH to the ‘off’ position.

Step 2. Rotate SWITCH COVER 90° and remove from TRACK.

Instructions for Lockable Aiming (Fig. 4)

Step 1. Aim fixture to desired position.

Step 2. To lock the fixture’s rotation horizontally, insert 0.05 allen wrench, provided, into hole at

housing base (Fig. 4). Turn clockwise to tighten.

Step 3. To lock the fixture’s rotation vertically, insert 0.05 allen wrench, provided, into hole at

fixture neck (Fig. 4). Turn clockwise to tighten.

FIG. 3

FIG. 2G

RACK POLARITY

INE

RELEASE

BUTTON

ONTACT

EAD

POLARITY

GROOVE

NSERT CONTACT

EAD AND TURN 90°

O POLARITY GROOVE

ND TRACK POLARITY

INE ARE ALIGNED

TRACK

SWITCH

COVER

FIG. 2H

POLARITY

ROOVE

RELEASE

UTTON

TRACK

OLARITY LINE

FIG. 4

VERTICAL

LOCK

HORIZONTAL

LOCK

HALO

´L´ Connectors

age 2

Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • 770.486.4800 • FAX 770.486.4801 CLP-0001288-rev2 704732INS