Vibration Isolation
Vibration Isolation
253
B-Line series Pipe Hangers & SupportsEaton
To help address the issues of vibration and noise control/dampening vibration in mechanical, refrigeration, HVAC and
electrical installations, Eaton offers the following B-Line series vibration isolation products. It is our continuing effort to offer
the industry quality support system products that meet the demands of today’s construction environment.
The following pages depict vibration isolation and noise control products that are commonly specified and required on
piping, duct and equipment, but not limited to mechanical rooms. As an aid in choosing the proper vibration control
device, the chart shown on the following page is a reference for obtaining Vibration Isolation Efficiency.
Considerations must be given to the desired deflection and the frequency (R.P.M.).
The Theory of Vibration Isolation
Background
Soils, floors, ceilings, walls, etc. deflect as the result of applied forces. Cyclical forces generated by machines result in work done on
the floors, etc. Under steady state conditions, this work is stored as potential energy in the floor each cycle and returned as work in
forcing the machine back to its equilibrium position. Disturbance is transmitted during this flexing.
Vibration Isolation is needed when disturbing force magnitudes are expected to be great enough to cause damage or annoyance.
Assumption Fact
1. We know the effects of vibration isolation (efficiency) Formula for calculation shown below.
2. We know the magnitude of the disturbing forces created Equipment manufacturers rarely provide these data.
by the machines These forces are seldom known except in generalities.
3. We know the magnitude of disturbing forces beyond Detailed calculations require so many simplifying assumptions
that the resulting answers have questionable value in addition
to being prohibitively expensive. Reliance is placed on brief
calculations, general rules, and past experience.
Consideration of items 1. and 2. is essential to determine acceptable isolation efficiency. Unfortunately manifold complexities prevent
inclusion of steps for determination of these efficiencies in this document.
Proper Sizing
Once it is determined as to what type of vibration dampening device is needed, weight loading is the next crucial step.
As a built in safety measure, take the actual weight of supported pipe or equipment (consider all accessories - i.e.
valves, insulation, brackets, etc...) and multiply by 1.25. Then refer to the sizing chart for the selected product to
determine part number.
Sizing: Divide weight of equipment by points of support to determine load requirement per support.
Example: 240 Lb.
(90.7 kg) piece of equipment, 4 support points, take 240 x 1.25 = 300 Lbs. (136.1kg) (safety
measure), then take 300 ÷ 4 = 75 Lbs. (34.0 kg) Specify appropriate vibration device rated at
75 Lbs.
(34.0 kg) for each of the support points.
If weight of equipment is unequally proportionate, select mounts to satisfy the weight distribution.
Vibration Isolation
Vibration Isolation Data
254
EatonB-Line series Pipe Hangers & Supports
Natural frequency of isolation system f
n
(cycles per minute)
Visualize a machine suspended barely above 4 springs (one on each corner). Now release the suspension. The machine will deflect
the springs and be pushed up and return a number of times with diminishing deflection until it comes to rest. The spring deflection
at rest is called the static deflection. The number of cycles per unit time is the natural frequency of the isolation system. Unlike
multi-degree of freedom floors with limitless natural frequencies, springs essentially have only one natural frequency.
Transmitted force f
t
(pounds) f
t
= f
d
(100% - isolation efficiency)
Note that fn must be compared to f
d
for satisfactory isolation efficiency. Also note that the force transmitted can be greater than
the disturbing force when f
n
is close to or equals f
d
. This condition is called resonance and is avoided in vibration isolation.
Natural frequency of floor or soil
Visualize the effect of dropping a load on the floor. This floor will deflect and spring back diminishingly a number of cycles until
it comes to rest. The number of these cycles per unit time is a natural frequency of the floor. It is essentially independent of
the magnitude of deflection and hence is a characteristic of a given floor if given a light tap or a hard jolt at the same location.
The floor has many natural frequencies. The lowest natural frequency is called the fundamental. It is characterized by maximum
deflection at mid span. The higher natural frequencies are generally less bothersome than the fundamental since they are less
likely to be excited by machines in common use and are more quickly damped. The greater a floor deflects under a given load,
the lower the fundamental frequency of that floor. Soft, springy floors have low fundamentals. Hard, solid floors have high
fundamentals.
Disturbing frequency f
d
(cycles per minute)
With few exceptions, the speed (RPM) of the machine will be most representative of the frequency of the disturbance.
Disturbances are more readily transmitted when the disturbing frequency is close to a natural frequency of the floor or soil.
For this reason, these characteristics are important considerations i designing a trouble-free installation.
Disturbing force f
d
(pounds)
The disturbing force causes the problem. It is constantly changing from maximum positive through zero to maximum negative
through zero to maximum positive each cycle. It results from unbalanced reciprocating and rotating masses. Its peak magnitude
varies from ounces to tons. From less than 1% to over 60% of the weight of some types of machines. Generally this force will
increase with time in a given machine as bearings wear, deposits form and moving parts get out of balance with each other.
1
static deflection (inches)
f
n
= 188
Vibration isolation efficiency % = 100% x 1 -
1
(f
d
÷
f
n
)
2
- 1
[ ]