1.SCOPE:
This specification covers the requirements for product performance of 1.25mm pitch SERIES wire to board
connector series.
2.CONSTRUCTION、DIMENSIONS 、 MATERIAL & PLATING:
See the attached drawings
3.RATINGS & APPLICABLE WIRES:
*: Including terminal temperature rise +30°C Max
4.PERFORMANCE:
4-1-1 Contact
Resistance
4-1-2 Insulation
Resistance
4-1-3 Dielectric
Withstandin
g
Voltage
4-1-4 Contact
Resistance
on Crimped
Portion
APPROVED CHECKED
BY BY
A2 2016.06.14
周傑亮
A1 2011.07.07
陳柏菘
A0 2011.04.10
陳柏菘
2011.04.10 2011.04.10
REV. DATE NAME
DESCRIPTION
Modify "5"
5mΩ max.
by dry circuit, 20mV max., 100mA.
董正一 童冠銘 陳柏菘
2011.04.10
REVISE
NEW RELEASE
Rated Current (max.)
Requirement
Ambient Temperature Range
-25°C ~ +85°C*
Test Description
1.00mm (max.)
Insulation O.D.
Item Standard
Rated Voltage (max.)
200V AC, DC
Mate connectors, measure by dry circuit, 20mV max.,
100mA. (Based upon JIS C5402 5.4)
MIL-STD-202 Method 302 Cond. B)
between adjacent terminal or ground. (Based upon No Breakdown
Crimp the applicable wire on to the terminal, measure
Mate connectors, apply 500V DC between adjacent
terminal or ground. (Based upon JIS C5402 5.2/
1000MΩ min.
Mate connectors, apply 900 VAC(<5ma) (rms) for 1
m
DOCUMENT NO: PS-12510-001
燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
PAGE: 1/4
PRODUCT SPECIFICATION
PRODUCT SERIES NAME: A12510 SERIES Wire to Board
Procedure
BY
4-1.ELECTRICAL PERFORMANCE
and Applicable Wires AWG #28 ,1A, AC, DC
WRITTEN
20mΩ max.
JIS C5402 5.1/MIL-STD-202 Method 301)
燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
PRODUCT SPECIFICATION
PRODUCT SERIES NAME A12510 SERIES
Wi t B d
PAGE
2/4
4-2-1 Insertion &
Withdrawal
Force
4-2.MECHANICAL PERFORMANCE
Test Description Procedure
Insert and withdraw connectors at the speed rate of
25 ± 3mm/minute.
PRODUCT SERIES NAME: A12510 SERIES Wire to Board
PAGE: 2/4
Requirement
Refer to paragraph 5
F
orce
4-2-2 Crimping
Pull Out
Force
(Based upon JIS C5402 6.8)
1.0kgf min.AWG #28
Fix the crimped terminal, apply axial
rate of 25 ± 3mm/minute.
pull out force on the wire at the speed
4-2-3 Terminal
Insertion
Force
4-2-4 Terminal/
Housing
Retention
1.0kgf max.
Insert the crimped terminal into the housing.
housing
25 ± 3mm/minute on the terminal assembled in the
1.0kgf min.
Apply axial pull out force at the speed rate of
Retention
Force
4-2-5 Durability Contact
Resistance
4
-
2
-
6
Vibration
Contact
housing
.
40mΩ max.
by the rate of 10 cycles per minute.
Appearance No Damage
When mated up to 30 cycles repeatedly
Amplitude: 1.5mm P-P
Sweep time: 10-55-10 Hz in 1 minute
Duration: 2 hours in each
4-2-6
Vibration
Contact
Resistance
4-2-7 Contact
40mΩ max.
Discontinuit
y
1μsec. max.
No Damage
40
Ω
490m/s² {50G}, 3 strokes in each
X.Y.Z. axes.
(
Based u
p
on JIS C0041/MIL-STD-202
Appearance
Method 201A)
(Based upon MIL-STD-202
X.Y.Z. axes
Duration:
2
hours
in
each
427
Contact
Shock Resistance
Discontinuit
y
1μsec. max.
40mΩ max.
Method 213B Cond. A)
(Based
upon
JIS
C0041/MIL STD 202