1.SCOPE:
This specification covers the requirements for product performance of 1.20mm pitch wire to board
connector series.
2.CONSTRUCTION、DIMENSIONS 、 MATERIAL & PLATING:
See the attached drawings
3.RATINGS & APPLICABLE WIRES:
AWG #28
AWG #30
*: Including terminal temperature rise
4.PERFORMANCE:
4-1-1 Contact
Resistance
4-1-2 Insulation
Resistance
4-1-3 Dielectric
Withstandin
g
Voltage
4-1-4 Contact
Resistance
on Crimped
Portion
APPROVED CHECKED
BY BY
A1 2015.09.18
周傑亮
A0 2012.09.03
劉包根
2012.09.03 2012.09.03
REV. DATE NAME
MIL-STD-202 Method 302 Cond. B)
Mate connectors, apply 500V AC (rms) for 1 minute
JIS C5402 5.1/MIL-STD-202 Method 301)
between adjacent terminal or ground. (Based upon
Crimp the applicable wire on to the terminal, measure
by dry circuit, 20mV max., 10mA.
WRITTEN
No Breakdown
Requirement
StandardItem
Mate connectors, apply 500V DC between adjacent
Ambient Temperature Range -25°C ~ +85°C*
Insulation O.D.
Rated Voltage (max.)
Rated Current (max.)
and Applicable Wires
0.70mm (max.)1.0A AC, DC
燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
terminal or ground. (Based upon JIS C5402 5.2/
100MΩ min.
20mΩ max.
Mate connectors, measure by dry circuit, 20mV max.,
10mA. (Based upon JIS C5402 5.4)
50V AC, DC
1.5A AC, DC
PAGE: 1/4
PRODUCT SPECIFICATION
PRODUCT SERIES NAME: A1200 SERIES-SMT TYPE
4-1.ELECTRICAL PERFORMANCE
ProcedureTest Description
DOCUMENT NO: PS-1200-001
Modify "5"
NEW RELEASE
DESCRIPTION
2012.09.03
BY
5mΩ max.
董正一 陳彥兆 劉包根
燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
PRODUCT SPECIFICATION
PRODUCT SERIES NAME
A1200
SERIES
SMT TYPE
PAGE
2/4
4-2-1 Insertion &
Withdrawal
Force
4-2.MECHANICAL PERFORMANCE
Insert and withdraw connectors at the speed rate of
Requirement
Refer to paragraph 4
PRODUCT SERIES NAME: A1200 SERIES-SMT TYPE
PAGE: 2/4
Test Description Procedure
25 ± 3mm/minute.
F
orce
4-2-2 Crimping
Pull Out
Force
1.0kgf min.
0.5kgf min.
Fix the crimped terminal, apply axial
AWG #28
pull out force on the wire at the speed
rate of 25 ± 3mm/minute.
AWG #30
(Based upon JIS C5402 6.8)
4-2-3 Terminal
Insertion
Force
4-2-4 Terminal/
Housing
Retention
Insert the crimped terminal into the housing.
0.3kgf min.
Apply axial pull out force at the speed rate of
25 ± 3mm/minute on the terminal assembled in the
housing
1.5kgf max.
Retention
Force
4-2-5 Pin
Retention
Force
4-2-6 Durability Contact
Resistance
Apply axial push force at the speed rate of
25 ± 3mm/minute.
When mated up to 50 cycles repeatedly
by the rate of 10 cycles per minute.
40mΩ max.
0.05kgf min.
housing
.
Resistance
4-2-7 Vibration Contact
Resistance
Amplitude: 1.5mm P-P
(Based upon MIL-STD-202
Method 201A
)
Duration: 2 hours in each
by
the
rate
of
10
cycles
per
minute
.
Sweep time: 10-55-10 Hz in 1 minute
Appearance No Damage
X.Y.Z. axes
Discontinuit
y
1μsec. max.
40mΩ max.
4-2-8 Physical Contact
Shock Resistance
(Based upon JIS C0041/MIL-STD-202
Method
201A)
1μsec. max.Discontinuit
y
40mΩ max.
Method 213B Cond. A)
490m/s² {50G}, 3 strokes in each
Appearance No Damage
X.Y.Z. axes.