PAGE: 1/4
PRODUCT SPECIFICATION
PRODUCT SERIES NAME: A1014 SERIES
燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
1.SCOPE:
This specification covers the requirements for product performance of 1.00mm pitch wire to board
connector series.
2.CONSTRUCTION、DIMENSIONS 、 MATERIAL & PLATING:
Sthtthdd i
See the attached drawings
3.RATINGS & APPLICABLE WIRES:
AWG #
28
Rated Current (max )
1
AAC DC
Insulation O D
Rated Voltage (max.)
StandardItem
50V AC, DC
AWG
#
28
AWG #30
AWG #32
*: Including terminal temperature rise
4 PERFORMANCE:
0.8A AC, DC
R
a
t
e
d
C
urren
t
(
max.
)
1
A
AC
,
DC
I
nsu
l
a
ti
on
O
.
D
.
Ambient Temperature Range -25°C ~ +85°C*
0.80mm (max.)
and Applicable Wires
1A AC, DC
4
.
PERFORMANCE
:
4-1-1 Contact
Resistance
4-1-2
Insulation
Mate connectors apply 500V DC between adjacent
4-1.ELECTRICAL PERFORMANCE
ProcedureTest Description Requirement
20mΩ max.
Mate connectors, measure by dry circuit, 20mV max.,
10mA. (Based upon JIS C5402 5.4)
4
-
1
-
2
Insulation
Resistance
4-1-3 Dielectric
Withstandin
g
Voltage
4
-
1
-
4
Contact
Mate
connectors
,
apply
500V
DC
between
adjacent
MIL-STD-202 Method 302 Cond. B)
terminal or ground. (Based upon JIS C5402 5.2/
100MΩ min.
Mate connectors, apply 250V AC (rms) for 1 minute
JIS C5402 5.1/MIL-STD-202 Method 301)
between adjacent terminal or ground. (Based upon
Crimp the applicable wire on to the terminal, measure
No Breakdown
4-1-4
Contact
Resistance
on Crimped
Portion
5mΩ max.
Crimp
the
applicable
wire
on
to
the
terminal
,
measure
by dry circuit, 20mV max., 10mA.
APPROVED CHECKED
BY BY
A2 2010.11.26
陳錦展
BY
歐陽
小強
伍建永
WRITTEN
謝瑞清
Modify "4-3-10&5"
陳錦展
A1 2009.04.16
歐陽小強
A0 2008.07.07
歐陽小強
2008.07.07 2008.07.07
REV. DATE NAME
歐陽
小強
伍建永
REVISE
NEW RELEASE
DESCRIPTION
謝瑞清
DOCUMENT NO: PS-1014-001
2008.07.07
y
燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
PRODUCT SPECIFICATION
PRODUCT SERIES NAME: A1014 SERIES
PAGE: 2/4
4-2-1 Insertion &
Withdrawal
Force
Insert and withdraw connectors at the speed rate of
Fi th i d t i l l i l
4-2.MECHANICAL PERFORMANCE
Test Description Procedure
25 ± 3mm/minute.
Requirement
Refer to paragraph 5
4-2-2 Crimping
Pull Out
Force
423
Terminal
0.3kgf min.
Fix the crimped terminal, apply axial
AWG #28
pull out force on the wire at the speed
AWG #32
1.0kgf min.
Insert the crimped terminal into the housing
rate of 25 ± 3mm/minute.
AWG #30 0.5kgf min.
(Based upon JIS C5402 6.8)
4
-
2
-
3
T
erm
i
na
l
Insertion
Force
4-2-4 Terminal/
Housing
Retention
Force
I
nser
t
th
e cr
i
mpe
d
t
erm
i
na
l
i
n
t
o
th
e
h
ous
i
ng.
Apply axial pull out force at the speed rate of
25 ± 3mm/minute on the terminal assembled in the
housing.
0.5kgf max.
0.5kgf min.
F
orce
4-2-5 Pin
Retention
Force
4-2-6 Latch Yield
Strength
4-2-7
Durability
Contact
0.3kgf min.
Apply axial push force at the speed rate of
25 ± 3mm/minute.
Mate connectors and pull apart until both latches
2.0kgf min.
break at the speed rate of 25 ± 3mm/minute.
When mated up to 30 cycles repeatedly
4
-
2
-
7
Durability
Contact
Resistance
4-2-8 Vibration Contact
Resistance
Amplitude: 1.5mm P-P
(Based upon MIL
-
STD
-
202
X.Y.Z. axes
iii
1
40mΩ max.
Duration: 2 hours in each
When
mated
up
to
30
cycles
repeatedly
by the rate of 10 cycles per minute.
No Damage
40mΩ max.
Sweep time: 10-55-10 Hz in 1 minute
Appearance
4-2-9 Physical Contact
Shock Resistance
(Based upon JIS C0041/MIL-STD-202
(Based
upon
MIL STD 202
Method 201A)
1
Di ti it
40mΩ max.
Method 213B Cond. A)
490m/s² {50G}, 3 strokes in each
Appearance No Damage
X.Y.Z. axes.
Discontinuit
y
1μsec. max.
1μsec. max.Discontinuit
y