g
燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
PRODUCT SPECIFICATION
PRODUCT SERIES NAME: A1013 SERIES-DUAL ROW SMT TYPE
PAGE: 1/4
1.SCOPE:
This specification covers the requirements for product performance of 1.00mm pitch wire to board
connector series.
2.CONSTRUCTION、DIMENSIONS 、 MATERIAL & PLATING:
See the attached drawings
3.RATINGS & APPLICABLE WIRES:
Item Standard
Rated Voltage (max.)
50V AC, DC
Rated Current (max.)
AWG #28
1A AC, DC
Insulation O.D.
and Applicable Wires
AWG #30
1A AC, DC 0.80mm (max.)
AWG #32
0.5A AC, DC
Ambient Temperature Range -25°C ~ +85°C*
*: Including terminal temperature rise
4.PERFORMANCE:
4-1.ELECTRICAL PERFORMANCE
Test Description Procedure Requirement
4-1-1 Contact
Mate connectors, measure by dry circuit, 20mV max.,
20mΩ max.
Resistance
10mA. (Based upon JIS C5402 5.4)
4-1-2 Insulation
Mate connectors, apply 500V DC between adjacent
Resistance
terminal or ground. (Based upon JIS C5402 5.2/
100MΩ min.
MIL-STD-202 Method 302 Cond. B)
4-1-3 Dielectric
Mate connectors, apply 500V AC (rms) for 1 minute
Withstandin
between adjacent terminal or ground. (Based upon No Breakdown
Voltage
JIS C5402 5.1/MIL-STD-202 Method 301)
4-1-4 Contact
Crimp the applicable wire on to the terminal, measure
5mΩ max.
Resistance
by dry circuit, 20mV max., 10mA.
on Crimped
Portion
APPROVED CHECKED
WRITTEN
BY BY
BY
A2
Modify "5"
2011.06.28
謝瑞清 伍建永 歐陽小強
A1
REVISE
2007.07.20
A0
NEW RELEASE
2007.05.08
REV.
DESCRIPTION
DATE
DOCUMENT NO: PS-1013-001
y
y
燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
PRODUCT SPECIFICATION
PRODUCT SERIES NAME: A1013 SERIES-DUAL ROW SMT TYPE
PAGE: 2/4
4-2.MECHANICAL PERFORMANCE
Test Description Procedure Requirement
4-2-1 Insertion &
Insert and withdraw connectors at the speed rate of
Withdrawal
25 ± 3mm/minute. Refer to paragraph 5
Force
Fix the crimped terminal, apply axial
AWG #28 1.6kgf min.
4-2-2 Crimping
pull out force on the wire at the speed
Pull Out
rate of 25 ± 3mm/minute.
AWG #30 0.8kgf min.
Force
(Based upon JIS C5402 6.8)
AWG #32 0.5kgf min.
4-2-3 Terminal
Insert the crimped terminal into the housing.
Insertion
0.5kgf max.
Force
4-2-4 Terminal/
Apply axial pull out force at the speed rate of
0.5kgf min.
Housing
25 ± 3mm/minute on the terminal assembled in the
Retention
housing.
Force
4-2-5 Pin
Apply axial push force at the speed rate of
Retention
25 ± 3mm/minute.
0.5kgf min.
Force
4-2-6 Durability
When mated up to 50 cycles repeatedly
Contact
40mΩ max.
by the rate of 10 cycles per minute.
Resistance
Amplitude: 1.5mm P-P
Appearance No Damage
Sweep time: 10-55-10 Hz in 1 minute
4-2-7 Vibration
Duration: 2 hours in each
Contact
40mΩ max.
X.Y.Z. axes
Resistance
(Based upon MIL-STD-202
Discontinuit
1μsec. max.
Method 201A)
490m/s² {50G}, 3 strokes in each
Appearance No Damage
X.Y.Z. axes.
4-2-8 Physical
(Based upon JIS C0041/MIL-STD-202
Contact
40mΩ max.
Shock
Method 213B Cond. A)
Resistance
Discontinuit 1μsec. max.