燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
PAGE
1/4
PRODUCT SPECIFICATION
PRODUCT SERIES NAME
A1008
SERIES
SMT TYPE
1.SCOPE:
This specification covers the requirements for product performance of 1.00mm pitch wire to board
connector series.
2 CONSTRUCTION
DIMENSIONS
MATERIAL & PLATING
PAGE: 1/4
PRODUCT SERIES NAME: A1008 SERIES-SMT TYPE
2
.
CONSTRUCTION
、
DIMENSIONS
、
MATERIAL
&
PLATING
:
See the attached drawings
3.RATINGS & APPLICABLE WIRES:
Rated Voltage (max )
200
VAC DC
StandardItem
AWG #28
AWG #30
AWG #32
AWG #34
AWG #36
Rated
Voltage
(ma
x.
)
200
V
AC
,
DC
1A AC, DC
Insulation O.D.Rated Current (max.)
and Applicable Wires
0.8A AC, DC 0.50mm (max.)
0.5A AC, DC
1A AC, DC
0.5A AC, DC
Ambient Temperature Range
-
25
°
C
~
+85
°
C
*: Including terminal temperature rise
4.PERFORMANCE:
Test Description
Requirement
Procedure
Ambient
Temperature
Range
-
25 C
~
+85 C
4-1.ELECTRICAL PERFORMANCE
4-1-1 Contact
Resistance
4-1-2 Insulation
Resistance
4-1-3 Dielectric
terminal or ground. (Based upon JIS C5402 5.2/
Mate connectors
,
a
pp
l
y
500V AC
(
rms
)
for 1 minu
t
Test
Description
Mate connectors, measure by dry circuit, 20mV ma
x
Requirement
100MΩ min.
Mate connectors, apply 500V DC between adjacent
Procedure
40mΩ max.
10mA. (Based upon JIS C5402 5.4)
MIL-STD-202 Method 302 Cond. B)
413
Dielectric
Withstanding
Voltage
4-1-4 Contact
Resistance
on Crimped
Portion
between adjacent terminal or ground. (Based upon
JIS C5402 5.1/MIL-STD-202 Method 301)
by dry circuit, 20mV max., 10mA.
Mate
connectors,
apply
500
V
AC
(rms)
for
1
minut
Crimp the applicable wire on to the terminal, meas
u
5mΩ max.
No Breakdown
APPROVED CHECKED
A3 2017.03.20
劉建芳
BY BY
WRITTEN
"Item 5" alteration BY
A2 2007.06.26
歐陽小強
A1 2007.01.09
歐陽小強
A0 2006.08.10
歐陽小強
REV. DATE NAME
REVISE
REVISE
NEW RELEASE
DOCUMENT NO: PS-1008-001
謝瑞清 呂長祈 歐陽小強
DESCRIPTION
燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
PRODUCT SPECIFICATION
PRODUCT SERIES NAME
A1008
SERIES
SMT TYPE
PAGE
2/4
4-2-1 Insertion &
Withdrawal
Force
25 ± 3mm/minute. Refer to paragraph 5
4-2.MECHANICAL PERFORMANCE
Test Description Procedure Requirement
Insert and withdraw connectors at the speed rate of
PRODUCT SERIES NAME: A1008 SERIES-SMT TYPE
PAGE: 2/4
F
orce
4-2-2 Crimping
Pull Out
Force
AWG #32 0.5kgf min.
Fix the crimped terminal, apply axial
1.0kgf min.
pull out force on the wire at the speed
rate of 25 ± 3mm/minute.
AWG #30 0.8kgf min.
(Based upon JIS C5402 6.8)
AWG #28
F
orce
4-2-3 Terminal
Insertion
g
Insert the crimped terminal into the housing.
AWG #34
AWG #36 0.2kgf min.
0.3kgf min.
05
kgf max
Insertion
Force
4-2-4 Terminal/
Housing
Retention
Force
4
-
2
-
5
Pin
Apply axial pull out force at the speed rate of
Apply axial push force at the speed rate of
0.5kgf min.
25 ± 3mm/minute on the terminal assembled in the
housing.
0
.
5
kgf
max
.
4-2-5
Pin
Retention
Force
4-2-6 Latch Yield
Strength
4-2-7 Durability Contact
Resistance
Apply
axial
push
force
at
the
speed
rate
of
25 ± 3mm/minute.
by
the rate of 10 c
y
cles
p
er minute.
When mated up to 50 cycles repeatedl
y
80mΩ max.
0.3kgf min.
Mate connectors and pull apart until both latches
7.0kgf min.
break at the speed rate of 25 ± 3mm/minute.
Resistance
4-2-8 Vibration Contact
Resistance
Duration: 2 hours in each
80mΩ max.
X.Y.Z. axes
Amplitude: 1.5mm P-P
by
the
rate
of
10
cycles
per
minute.
Appearance No Damage
Sweep time: 10-55-10 Hz in 1 minute
(Based upon MIL-STD-202
Discontinuit
y
1μsec. max.
Method 201A)
4-2-9 Physical Contact
Shock Resistance
490m/s² {50G}, 3 strokes in each
Appearance No Damage
X.Y.Z. axes.
)
(Based upon JIS C0041/MIL-STD-202
80mΩ max.
Method 213B Cond. A)
Discontinuit
y
1μsec. max.