1.SCOPE:
This specification covers the requirements for product performance of 1.00mm pitch wire to board
connector series.
2.CONSTRUCTION、DIMENSIONS 、 MATERIAL & PLATING:
See the attached drawings
3.RATINGS & APPLICABLE WIRES:
AWG #28
AWG #30
AWG #32
*: Including terminal temperature rise
4.PERFORMANCE:
4-1-1 Contact
Resistance
4-1-2 Insulation
Resistance
4-1-3 Dielectric
Withstanding
Voltage
4-1-4 Contact
Resistance
on Crimped
Portion
APPROVED
CHECKED
BY BY
A1 2007.06.26
A0 2006.08.14
REV. DATE
WRITTEN
董正一 伍建永
No Breakdown
BY
DESCRIPTION DOCUMENT NO: PS-1007-001
NEW RELEASE
歐陽小強
REVISE
Mate connectors, apply 500V AC (rms) for 1 minute
JIS C5402 5.1/MIL-STD-202 Method 301)
between adjacent terminal or ground. (Based upon
Crimp the applicable wire on to the terminal, measure
by dry circuit, 20mV max., 10mA.
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
JOY DAY INDUSTRIAL CO., LTD.
terminal or ground. (Based upon JIS C5402 5.2/ 500MΩ min.
30mΩ max.
Mate connectors, measure by dry circuit, 20mV max.,
10mA. (Based upon JIS C5402 5.4)
100V AC, DC
0.8A AC, DC
PAGE: 1/4
PRODUCT SPECIFICATION
PRODUCT SERIES NAME: A1007 SERIES-SMT TYPE
4-1.ELECTRICAL PERFORMANCE
ProcedureTest Description Requirement
StandardItem
Mate connectors, apply 500V DC between adjacent
5mΩ max.
Ambient Temperature Range
MIL-STD-202 Method 302 Cond. B)
-25°C ~ +85°C*
1A AC, DC Insulation O.D.
Rated Voltage (max.)
and Applicable Wires 0.9A AC, DC 0.60mm (max.)
Rated Current (max.)
4-2-1Insertion &
Withdrawal
Force
4-2-2 Crimping
Pull Out
Force
4-2-3 Terminal
Insertion
Force
4-2-4 Terminal/
Housing
Retention
Force
4-2-5 Pin
Retention
Force
4-2-6 Durability Contact
Resistance
4-2-7 Vibration Contact
Resistance
4-2-8 Physical Contact
Shock Resistance
When mated up to 50 cycles repeatedly
by the rate of 10 cycles per minute.
No Damage
60mΩ max.
Sweep time: 10-55-10 Hz in 1 minute
Appearance
No Damage
X.Y.Z. axes.
X.Y.Z. axes
Discontinuity
1μsec. max.
60mΩ max.
Duration: 2 hours in each
1μsec. max.
Discontinuity
60mΩ max.
Method 213B Cond. A)
490m/s² {50G}, 3 strokes in each
Appearance
(Based upon JIS C0041/MIL-STD-202
Amplitude: 1.5mm P-P
(Based upon MIL-STD-202
Method 201A)
0.5kgf min.
0.3kgf min.
Apply axial push force at the speed rate of
25 ± 3mm/minute.
Apply axial pull out force at the speed rate of
25 ± 3mm/minute on the terminal assembled in the
housing.
rate of 25 ± 3mm/minute.
AWG #30 0.8kgf min.
(Based upon JIS C5402 6.8)
Test Description Procedure
25 ± 3mm/minute.
Requirement
Refer to paragraph 5
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
JOY DAY INDUSTRIAL CO., LTD.
PRODUCT SPECIFICATION
PRODUCT SERIES NAME: A1007 SERIES-SMT TYPE
PAGE: 2/4
0.5kgf max.
1.0kgf min.
4-2.MECHANICAL PERFORMANCE
Insert the crimped terminal into the housing.
Insert and withdraw connectors at the speed rate of
Fix the crimped terminal, apply axial
AWG #28
pull out force on the wire at the speed
AWG #32 0.5kgf min.