燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
PRODUCT SPECIFICATION
1.SCOPE:
This specification covers the requirements for product performance of 0.80mm pitch wire to board
connector series.
PAGE: 1/5
PRODUCT SERIES NAME: A0800 SERIES
2.CONSTRUCTION、DIMENSIONS 、 MATERIAL & PLATING:
See the attached drawings
3.RATINGS & APPLICABLE WIRES:
dl ( )
StandardItem
li O
*: Including terminal temperature rise
4 PERFORMANCE:
30V AC, DC
Rate
d
Vo
l
tage
(
max.
)
Rated Current (max.)
and Applicable Wires
-25°C ~ +85°C*
Insu
l
at
i
on
O
.D.
Ambient Temperature Range
0.38mm (max.)
AWG #32 0.5A AC, DC
4
.
PERFORMANCE:
4-1-1 Contact
Resistance
4
-
1
-
2
Insulation
20mΩ max.
4-1.ELECTRICAL PERFORMANCE
Requirement
Mate connectors apply 500V DC between adjacent
Mate connectors, measure by dry circuit, 20mV max.,
10mA. (Based upon JIS C5402 5.4)
ProcedureTest Description
412
Insulation
Resistance
4-1-3 Dielectric
Withstandin
g
Voltage
4-1-4 Contac
t
terminal or ground. (Based upon JIS C5402 5.2/
100MΩ min.
I.D.T. the a
licable wire on to the terminal, measure
MIL-STD-202 Method 302 Cond. B)
No Breakdown
Mate
connectors
,
apply
500V
DC
between
adjacent
Mate connectors, apply 200V AC (rms) for 1 minute
JIS C5402 5.1/MIL-STD-202 Method 301)
between adjacent terminal or ground. (Based upon
Resistance
on I.D.T.
Portion
10mΩ max.
by dry circuit, 20mV max., 10mA.
APPROVED CHECKED
BY BY
WRITTEN
BY
A1 2013.12.23
劉包根
A0 2012.08.03
陳錦展
2012.08.03 2012.08.03
REV. DATE NAME
DOCUMENT NO: PS-0800-002
陳錦展
2012.08.03
董正一 陳彥兆
DESCRIPTION
NEW RELEASE
A
dd "24P"Insertion And Withdrawal Forc
燦 達 電 子 工 業 股 份 有 限 公 司
JOINT TECH ELECTRONIC INDUSTRIAL CO., LTD.
PRODUCT SPECIFICATION
4-2-1 Insertion &
Withdrawal
Test Description Procedure
4-2.MECHANICAL PERFORMANCE
25 ± 3mm/minute.
Requirement
Refer to paragraph 5
Insert and withdraw connectors at the speed rate of
PRODUCT SERIES NAME: A0800 SERIES
PAGE: 2/5
Force
Axial
4-2-2 I.D.T. direction
Pull Out
Force Vertical
direction
(Based upon JIS C5402
0.6kgf min.
0.3kgf min.
68)
AWG #32
AWG #32
apply axial pull out force
on the wire at the speed
Fix the I.D.T. terminal,
rate of 25 ± 3mm/minute.
4-2-3 Pin
Retention
Force
4-2-4 Durability Contact
Resistance
0.2kgf min.
Apply axial push force at the speed rate of
25 ± 3mm/minute.
Amplitude: 1 5mm P P
6
.
8)
When mated up to 50 cycles repeatedly
by the rate of 10 cycles per minute.
40mΩ max.
4-2-5 Vibration Contact
Resistance
Sweep time: 10-55-10 Hz in 1 minute
Appearance
X.Y.Z. axes
Discontinuit
y
1μsec. max.
40mΩ max.
Duration: 2 hours in each
Amplitude:
1
.
5mm
P
-
P
490m/s
²
{50G} 3 strokes in each
Method 201A)
(Based upon MIL-STD-202
No Damage
4-2-6 Physical Contact
Shock Resistance
X.Y.Z. axes.
1μsec. max.Discontinuit
y
(Based upon JIS C0041/MIL-STD-202
40mΩ max.
Method 213B Cond. A)
490m/s
{50G}
,
3
strokes
in
each
Appearance No Damage