Liquid Release Agent
Description:
A silicone compound used to coat metals to act as a release agent to stop epoxies and urethanes from adhering to parts.
Intended Use:
Industrial Use: Any metal surfaces, alloys, porous castings, rubber surfaces, plastics, and concrete that need to
prevent having any polymers sticking to the surface
Features: Releases over multiple uses
Silicone Oil
Limitations:
Suitability of product is determined by the end user for their application and process.
Typical
Technical data should be considered representative or typical only and should not be used for specification purposes.
Physical
Properties: Uncured
Flashpoint (TCC method)
> 19 °F ( > -7°C)
Surface
1. Thoroughly clean the surface with Devcon® Cleaner Blend 300 to remove all oil, grease and dirt.
Preparation:
2. Grit blast surface area with 8-40 mesh grit, or grind with a coarse wheel or abrasive disc pad, to create increased surface
area for better adhesion (Caution: An abrasive disc pad can only be used provided white metal is revealed).
Desired profile is 3-5mil, including defined edges (do not "feather-edge” epoxy).
Note: For metals exposed to sea water or other salt solution, grit-blast and high-pressure-water-blast the area, then leave
overnight to allow any salts in the metal to “sweat” to the surface. Repeat blasting to “sweat out” all soluble salts. Perform
3. Clean surface again with Devcon® Cleaner Blend 300 to remove all traces of oil, grease, dust or other foreign
substances from the grit blasting.
WORKING CONDITIONS: Ideal application temperature is 55°F to 90°F. In cold working conditions, directly heat repair
area to 100-110°F (38-43°C) prior to applying epoxy and maintain at this temperature during product cure to dry off
any moisture, contamination or solvents, as well as to achieve maximum performance properties.
Mixing
No Mixing required - Use adequate ventilation is necessary when mixing this product.----
Instructions:
Application
Take a clean lint-free cloth and pour a generous amount of Release Agent onto the cloth. Lightly rub out the part or piece
Instructions:
of equipment gently, leaving a thin, shiny coat. Let dry!
Storage:
Store at room temperature, 70°F (21°C).
Compliances:
None
Chemical
Rating chemical resistance is not necessary for this product.
Resistance:
Precautions: FOR INDUSTRIAL USE ONLY: Please refer to the appropriate Safety Data Sheet prior to using this product.
Warranty:
ITW Performance Polymers will replace any material found to be defective. Because the storage, handling and application of this material
is beyond our control, we can accept no liability for the results obtained.
Technical Data Sheet
Version 3. 04/2023
chloride contamination test to determine soluble salt content (should be no more than 40ppm).
4. Repair surface as soon as possible to eliminate any changes or surface contaminants.
Order Item No. Package Size
Information:
19600
1 pt. (0.47 L)
Contacts:
www.itwpp.com
ITW Performance Polymers (EMEA) ITW Performance Polymers (US)
Bay 150, Shannon Industrial Estate 30 Endicott Street
Shannon, County Clare, Ireland V14 DF82 Danvers, MA 01923 USA
TEL: +353 61 771 500 TEL: 855 489 7262
FAX: +353 61 471 285 FAX: 978 774 0516
Email: customerservice.shannon@itwpp.com Email: info@itwpp.com
Disclaimer:
Product Use: The information herein is based upon good faith testing that ITW PP believes are reliable, but the
accuracy or completeness of such information is not guaranteed. Many factors beyond ITW PP control and
uniquely within user’s knowledge and control can affect the use and performance of an ITW PP product in a
particular application. Given the variety of influencers on performance, the data here is not intended to substitute
end user testing. It is the end users sole responsible for evaluating any ITW PP product and determining whether it
is fit for a particular purpose and suitable for user’s design, production, and final application.
Exclusion of Warranties: As to the herein described materials and test results, there are no warranties which
extend beyond the description on the face hereof. ITW PP makes no other warranties, express or implied,
including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. Since the
use of the herein described involves many variables in methods of application, design, handling and/or use, the
user, in accepting and using these materials, assumes all responsibility for the end result. ITW PP shall not
otherwise be liable for loss of damages, whether direct, indirect, special, incidental, or consequential, regardless of
the legal theory asserted, including negligence, warranty, or strict liability.