ITW Performance Polymers
30 Endicott Street
Danvers, MA 01923
(855) 489-7262
Technical Data Sheet
Permatex
Bearing Mount for
Relaxed Fits
AAM Revised 09/14
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT ITW PERFORMANCE POLYMERS TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.
ITW PERFORMANCE POLYMERS 30 ENDICOTT STREET, DANVERS, MA 01923 PHONE (855) 489-7262
PRODUCT DESCRIPTION
Permatex
Bearing Mount for Relaxed Fits is a high strength,
single component anaerobic retaining adhesive for cylindrical
joints. It is a green colored liquid resin that hardens and cures
in the absence of air. Permatex
Bearing Mount for Relaxed
Fits self-hardens into a tough plastic material when it is
confined between close-fitting metal parts. The cured
adhesive is a thermoset plastic suitable for exposure to most
solvents and engine fluids. OEM Specified. NSF White Book
registered.
PRODUCT BENEFITS
•
No mixing
•
No curing outside of joint
•
Prevents fretting and corrosion
•
Allows the use of slip fit or press fit
•
For use on assemblies with gaps up to 0.015” diametral
TYPICAL APPLICATIONS
•
Used to bond cylindrical fitting parts
•
Replaces set screws
•
Replaces clamp rings
•
Replaces snap ring
•
Wheel bearings
•
Idler shafts
•
Bearings
DIRECTIONS FOR USE
1.
Remove any grease or oil by using Permatex
Brake &
Parts Cleaner.
2. For slip fitted assemblies, apply adhesive around the
leading edge of the collar and use a rotating motion
during assembly.
3. For press fits, adhesive should be applied thoroughly to
both bond surfaces and assembled at high press-on
rates.
4. For shrink fitted assemblies, the adhesive should be
coated onto the pin; the collar should then be heated to
create sufficient clearance for free assembly.
5.
For faster cure rates, use Permatex
Surface Prep on
both surfaces.
6. Parts should not be disturbed until sufficient handling
strength is achieved.
7. Any material that is on the outside of the assembly will
not cure. Wipe off with a dry cloth.
PROPERTIES OF UNCURED MATERIAL
Typical Value
Chemical Type
Methacrylate ester
Appearance
Green liquid
Specific Gravity @ 77ºF
1.1
Viscosity
, cps
1250
Flash Point, COC, ºF
>200°
Cure Speed Hardens in 4 hours
Full cure in 24 hours
For Cleanup
1. Residual liquid films outside the joints are readily soluble
in Permatex
Brake & Parts Cleaner.
2. Cured product can be removed with a combination of
soaking in Permatex
Gasket Remover and mechanical
abrasion such as a wire brush.
For Disassembly
1. Apply localized heat to assembly to approximately 232°C
(450°F). Disassemble while hot.
For Reassembly
1. Remove any loose product from the assembly.
2. Apply primer to mating parts.
3. Assemble as per directions.
PERFORMANCE OF CURED MATERIAL
Temperature Resistance - -65°F to 300°F
Corrosivity - None (Slightly acidic, may discolor some
metals.)
Maximum gap fill - .015" diametral
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
ORDERING INFORMATION
Part Number
Container Size
68050 50 ml bottle
STORAGE
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8°
and 28°C
(46°
and 82°F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent
contamination of unused product, do not return any material to
its original container.
Technical Data Sheet Bearing Mount for Relaxed Fits
Permatex is a trademark of Permatex, Inc. © 2014 Permatex, Inc. All rights reserved
NOTE
The data contained herein are furnished for information only
and are believed to be reliable. We cannot assume
responsibility for the results obtained by others over whose
methods we have no control. ITW Permatex, Inc.
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Permatex,
Inc. products and disclaims any liability for consequential
or incidental damages of any kind, including lost profits.
This product may be covered by one or more United States or
foreign patents or patent applications.