ORDERING INFORMATION

STOCK NO.: 12750

PACKAGE SIZE: 2USG (7.56L)

DESCRIPTION

A 100% solids, 2-component Novalac

Epoxy, self-levelling, chemical-resistant

coating.

RECOMMENDED APPLICATIONS

• Excellent resistance to a range of

acids including 98% Sulphuric.

• Primary and secondary containment

for aggressive chemicals.

• Protecting oors from chemical

attack.

APPROVALS

• Approved in the U.S. for use in meat

and poultry processing plants.

• Accepted by Canadian Department

of Agriculture Food Safety Service.

PRODUCT DATA

TYPICAL PHYSICAL PROPERTIES

COLOUR LIGHT GREY

MIX RATIO BY VOLUME 1.45: 1

MIX RATIO BY WEIGHT 1.7 : 1

% SOLIDS BY VOLUME 100

POT LIFE AT 25

C/ MINS 35

SPECIFIC VOLUME CC/KG 885

CURED SHRINKAGE CM/CM N/A

DENSITY G/CM

1.13

TEMPERATURE RESISTANCE /

C Wet 50

C Dry 90

COVERAGE 2.5m

/L @ 0.40mm

CURED HARDNESS / SHORE D 85

DIELECTRIC STRENGTH KV/MM N/A

ADHESIVE TENSILE SHEAR / MPA N/A

COMPRESSIVE STRENGTH MPA N/A

COEFFICIENT OF THERMAL EXPANSION X10

-6

CM/CM/

N/A

THICKNESS PER COAT / MM 0.20mm

FUNCTIONAL CURE TIME /HOURS 24

FULL CURE (MAXIMUM CHEMICAL RESISTANCE) / DAYS *

MINIMUM RECOAT TIME / HOURS 3

MAXIMUM RECOAT TIME / HOURS 8

MIXED VISCOSITY /CPS (WHERE APPLICABLE) 3600

* Full cure can be accelerated by heating to 80oC for 4 hours after the functional cure time

TECHNICAL DATA SHEET – EPOXY COAT 7000 AR

Revised: 05/2018

A 100% SOLIDS, 2-COMPONENT NOVALAC EPOXY, SELF-LEVELLING,

CHEMICAL-RESISTANT COATING

TECHNICAL DATA SHEET – EPOXY COAT 7000 AR

CHEMICAL RESISTANCE - 7 DAYS ROOM TEMPERATURE CURE (30 DAYS)

POOR FAIR VERY GOOD EXCELLENT

ACETIC ACID 10% •

CUTTING OIL •

TOLUENE •

GASOLINE (UNLEADED) •

HYDROCHLORIC ACID 37% •

METHYL ETHYL KETONE (MEK) •

METHYLENE CHLORIDE •

SODIUM HYPOCHLORITE 5% (BLEACH) •

SODIUM HYDROXIDE 50% •

SULPHURIC ACID 98% •

POTASSIUM HYDROXIDE 40% •

Excellent = +/- 1% weight change, Very Good = +/- 1-10% weight change, Fair = +/- 10-20% weight change, Poor = > 20% weight change

APPLICATION INFORMATION

SURFACE PREPARATION

For METAL SURFACES, rstly degrease and then an

abrasive blast to SA 2½, if conditions mean this is not

practical then use of a wire brush or sandpaper to remove

rust and scale from the surface to be protected is a bare

minimum. This prep should be followed by dedusting before

proceeding with the coating process.

For NEW POURED CONCRETE, allow to fully cure (28 days

@ 70°F) prior to application. Remove any curing membrane

and laitance by wet or dry abrasive blasting, high pressure

water jetting or sanding An environmentally safe acid etch is

also suitable.

For OLD CONCRETE, depending on previous use, thoroughly

clean surface with a greasecutting detergent to remove

grease and oils if required. Remove any loose or unsound

concrete by scarifying, wet or dry abrasive blasting, high

pressure water jetting sanding, or grinding.

For PREVIOUSLY COATED CONCRETE, it is recommended

that any existing coating be completely removed in order

that the concrete surface is exposed, any coating applied

onto an existing coating could have an adverse reaction

with it or reduce the bond strength of said original coating

resulting in premature failure of the system.

For any concrete surface it is important to ll large holes

and undertake appropriate crack repairs with a suitable

patching compound before proceeding.

Devcon Concrete Sealer 100 or Epoxy Concrete Sealer can

be applied to shot-blasted or etched concrete surfaces to

seal prior to the application of other Devcon Floor Savers™

products although it is not essential.

MIXING

1. Pour hardener into resin.

2. Mix for about three minutes using a propeller-type Jiffy

Mixer Model ES (or equivalent) until a uniform colour is

achieved.

APPLICATION

For best results, Epoxy Coat 7000 AR should be stored and

applied at room temperature.

Onto Steel the surface should be prepared as described

above and then the Epoxycoat 7000AR can be applied

by brush or roller to the desired thickness in the required

number of coats.

Onto concrete, Epoxy Coat 7000 AR can be applied by

squeegee for horizontal surfaces, then “back rolled” for a

smooth nish with a short or medium nap roller. For vertical

surfaces it can be applied by either brush or roller taking

care not to over apply or the nish will be left with runs in it.

Coverage will vary depending on surface condition.

Epoxy Coat 7000 AR produces a smooth nish, which can

be slippery, especially when wet. As such for any walkways

it is recommended that a non-skid aggregate is added to

the coating. Cure gures quoted in the Product data section

are based on RT cure.

SHELF LIFE & STORAGE

A shelf life of 2 years from date of manufacture can be

expected when stored at room temperature.

PRECAUTION

For complete safety and handling information, please refer

to Material Safety Data Sheets prior to using this product.

WARRANTY

ITW Performance Polymers will replace any material found

to be defective. Because the storage, handling and applica-

tion of this material is beyond our control we can accept no

liability for the results obtained.

DISCLAIMER

All information on this data sheet is based on laboratory

testing and is not intended for design purposes.

ITW Performance Polymers makes no representations or

warranties of any kind concerning this data.

For product information visit www.devconeurope.com

alternatively for technical assistance please call +353 61 771 500.

ITW PERFORMANCE POLYMERS