Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1006F 2023
METAL OXIDE VARISTORS TNR
TM
TAPING SPECIFICATIONS
●This Specifies taping specifications for varistors which have normal disk
diameter of 5 to 15mm and nominal varistor voltage of 15 to 510V.
◆PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
T N D 1 2 V - 471 K T F A A A A 0
Category
Product Form
Size Varistor Voltage Varistor
Voltage
Tolerance
Form-A Form-B
(Parallel)
Note : The Code (T1,T15,T2,T25,T8,T7) are the old taping code.
TBB (T7)
TFB (T8)
Feed hole pitch
15.0mm
Code Type
Varistor Volt. Tolerance
φ1515
Taping Code
Series
05
07
09
The first two digits are sighificant figures and
the third one denote the number of following zeros.
Varistor Voltage
Lead Style
Series
V Series
Code
V-
Design code
φ1010
Size
φ5
φ7
Disk Type
Product Form
φ12
φ14
φ9
Code
ND
Code
12
14
Category
Metal Oxyde Varistor TNR
Code
T
TFA (T15)
TBA (T25)
5V,7V,9V,9H
Code
±10％K
－ Crimped (Form-B)
Straight (Form-B)
Crimped (Form-A)
Crimped (Form-B)
Straight (Form-A)
Straight (Form-B)
Feed hole pitch
Code
12.7mm
TFA (T15)
TBA (T25)
TEA (T1)
TAA (T2)
－
－
－
10V,12V,14V
H- H Series
－
－
－
－
Straight (Form-A)
Crimped (Form-A)
Crimped (Form-B)
Straight (Form-B)TBA (T25)
TEA (T1)
TFA (T15)
TAA (T2)
12H,15H
48
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1006F 2023
METAL OXIDE VARISTORS TNR
TM
TAPING SPECIFICATIONS
◆5V, 7V, 9V, 9H : TYPE TFA(T15) (Crimped Lead)
◆TYPE TFA(T15)
H1
H
H0
P0
P1
W2
W0
W
t
φ
D0
D
P P2
ΔP
T
F
W1
1.0 MAX.
L
J
Dimensions (mm)CodeParameter
Refer to the applicable detail spec
Refer to the applicable detail spec
Cumulative pitch error : ±1 mm/20 pitches
Measured at the upper end of tape
Please refer to the above list
Diameter of component
Thickness of component
Lead diameter
Pitch of component
Feed hole pitch
Feed hole diameter
Feed hole center to lead
Feed hole center to component center
Feed hole position
Lead spacing
Deviation across tape
Deviation along tape
Carrier tape width
Hold down tape width
Tape thickness
Total tape thickness
Hold down tape position
Seating plane height
Component height
Lead position
Defective article cut position
D
T
φd
P
P0
φD0
P1
P2
W1
F
Δh
ΔP
W
W0
t2
t1
W2
H0
H1
J
L
-
-
0.6±0.05
12.7±1.0
12.7±0.3
4.0±0.2
3.85±0.7
6.35±1.3
9.0±0.5
5.0±0.8
0±2.0
0±1.0
18.0±
5.0 Min.
1.5 Max.
0.6±0.3
3.0 Max.
6.0 Max.
11.0 Max.
1.0
0.5
5.0 Min.
3.0 Max.
16.0±0.5
-
φd
Δh
Note
5V 7V 9V 9H
Height (H Max.) 13.0 14.5 17.5 16.0
Component Heigh
t
(H1 Max.) 30.0 31.0 34.0 33.0
Type
49